Results 1 to 10 of 10
  1. #1
    Member
    Join Date
    Oct 2007
    Location
    Kingsport
    Posts
    158

    Got a question about Johnson 150

    I have a Johnson 150 Fastrike 1993 and i pulled my boat out of the water the other day lowered the motor to let the water drain from the motor and noticed something that i had never noticed before. Right around the vents on the lower part of the motor about two inches to the right towards the front of the motor there is a small pin hole that had water coming out of it. Would this be a problem i have no idea how it got there or anthing i dont even know if it has always been there i just walked back there and noticed water coming out of it right there around those vents. Im assuming it will not hurt anything since right there close to that is the vents that suck the water up or filter through or something. Can any of you tell me if this is a problem.



  2. Member
    Join Date
    Oct 2007
    Location
    Kingsport
    Posts
    158
    #2

    Re: Got a question about Johnson 150 (booneangler)

    you can see it is about 2 inches to the right of that vent.



  3. Member
    Join Date
    Oct 2007
    Location
    Kingsport
    Posts
    158
    #3

    Re: Got a question about Johnson 150 (booneangler)

    well i just called the boat shop and talked to them and they said that was a drain for the power something i cant remember what they said.



  4. SC Club Moderator ChampioNman's Avatar
    Join Date
    May 2004
    Location
    Crawfordville, FL/Lake Hartwell, SC
    Posts
    72,150
    #4

    Re: Got a question about Johnson 150 (booneangler)

    All OMC/BRP standard gear cases have that hole.

  5. Member
    Join Date
    Oct 2007
    Location
    Kingsport
    Posts
    158
    #5

    Re: Got a question about Johnson 150 (ChampioNman)

    i guess the paint is just falling off around the hole then. You see where it is coming off but what do you excpect it is a 1991 motor.



  6. Member Fiddlefarter's Avatar
    Join Date
    Mar 2005
    Location
    Smith Creek, FL
    Posts
    8,696
    #6

    Re: Got a question about Johnson 150 (booneangler)

    You can use CLR cleaner to get that hard water stain off, where the water has drained out of that hole since 1991.

  7. Member
    Join Date
    Oct 2007
    Location
    Kingsport
    Posts
    158
    #7

    Re: Got a question about Johnson 150 (Fiddlefarter)

    this may seem stupid but what is CLR cleaner. Where can i get this at.



  8. SC Club Moderator ChampioNman's Avatar
    Join Date
    May 2004
    Location
    Crawfordville, FL/Lake Hartwell, SC
    Posts
    72,150
    #8

    Re: Got a question about Johnson 150 (booneangler)

    Calcium Lime and Rust it is a stain remover they advertise it on TV all the time most any grocery store has it in the cleaning section. I wouldn't sweat it though you've got cavitation peel behind the water inlet screens.

  9. Member Fiddlefarter's Avatar
    Join Date
    Mar 2005
    Location
    Smith Creek, FL
    Posts
    8,696
    #9

    Re: Got a question about Johnson 150 (ChampioNman)

    What he said...There really wasn't any reason I posted that other than I figured that you were looking that that hole and might want to get the stain off.

  10. Member
    Join Date
    Sep 2006
    Location
    139 Wool Ln Charleston Tn. 37310.
    Posts
    2,080
    #10

    Re: Got a question about Johnson 150 (booneangler)

    That's a drain hole for a water cavity in the gearcase, if not open, it would allow water to freeze and possibly burst your housing. Not sure about the "Power something drain" you were told, that's a new one on me.

Similar Threads

  1. Johnson 175 Question
    By Flash5150 in forum Evinrude/Johnson Motors
    Replies: 11
    Last Post: 08-21-2011, 07:38 PM
  2. 99 Johnson 115 question
    By plang in forum Evinrude/Johnson Motors
    Replies: 3
    Last Post: 08-14-2011, 11:11 AM
  3. Johnson 115 question
    By plang in forum Evinrude/Johnson Motors
    Replies: 4
    Last Post: 05-28-2010, 01:53 PM
  4. 200 johnson question
    By Grumpy in forum Evinrude/Johnson Motors
    Replies: 2
    Last Post: 04-21-2008, 04:22 PM
  5. Johnson 150 Question
    By Bass Ackwards in forum Evinrude/Johnson Motors
    Replies: 2
    Last Post: 02-19-2007, 10:31 PM