Anyone know of "Trailers Inc" and grease seal part # (Skeeter boat trailer)

[Starfire175]

I have a cr-21 trailer from "trailers inc" under my starfire. Its the factory trailer from what I can tell, but I cant find any info on it anywhere. Im trying to replace the seals on the hubs, but the people at NAPA cant help me since I dont have a part number.

I took off one of the seals, and of course, there is no numbers or anything on it. From my measurements, then looking at a few places for seals online, it seems like the closest thing is a 2.33" x 1.68" seal...but Napa doesnt have one in that size (or the guy wasnt looking in the right spot).

Anyone have any info on a seal part number that Napa could cross reference? If it helps, the inner bearing is 44649.

[Tritonbmc]

Call Lyn at UFP

[Starfire175]

I got the seal size from their site, but Im looking for a number so the guy at napa can x-reference it. I dont have time to wait for one to be shipped to me, worse comes to worse I can go to a marina (nearest one is about 45 minutes away). I didnt think it would take rocket science to find a seal number since many people on here talked about just going to napa and getting one.

Worse yet I dont know who Trailers Inc is or who they have become.

[Ba$$n]

Should be NOK AD2527E.

Good luck with the auto stores they could not even match up the bearing numbers with the way the manufacturers lable their products. I buy the seals and bearings from UFP and avoid the hassle of the auto parts stores. Their computers always ask for a vehicle manufacture and model year, if they can't put that info in the guy at the counter is lost.

[Lyn O. Dyer]

If you have 44694 inner & outer brgs, your axle is a 1500#-2500#, and uses a 1.98x1.38 seal , Chicago Rawhide # 13557, or National # 482163N...

[Lyn O. Dyer]

look on page 4 here.....http://ufpnet.com/PDF/Trailer%20Budd...aintenance.pdf..

[Lyn O. Dyer]

my bad ...44649...lol..

[Starfire175]

Thanks for the info guys. I measured the hub opening with my micrometer, so I know it is 2.33. The outside bearing isnt the same number (I dont remember what it is right now). The old bearing inner lip diameter was a hare over 1.7", but I figured that it was old enough it may have shrank from the 1.68" size.

[Brock]

I will get you a number by noon today as soon as my wife gets back with the truck.
You are correct on the seal size I just went through the same stuff, auto stores carry it it is a common part.

Ron

[Brock]

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Brock &raquo;</TD></TR><TR><TD CLASS="quote">I will get you a number by noon today as soon as my wife gets back with the truck.
You are correct on the seal size I just went through the same stuff, auto stores carry it it is a common part.

Ron</TD></TR></TABLE>part# 15234VB this converts to Federal Mogul #203013
Any parts store can convert the first number to their stock number, took me three trips not all hubs have the same ID (seal OD) with your bearing set.

[Tx Champ]

Just for the record and not to take away from the seal discussion, but Trailers Inc or TI trailers is a division of EZ Loader and now known as EZ Loader Custom Boat Trailers.

[Starfire175]

Thanks for the part #'s brock, and the ezloader info tx champ.

I ended up having to order them online because none of the marina's within 100 miles carried them, and the parts store was worthless without a number to cross reference them with. I am going to write down the numbers now though for next time.

Thanks guys =D

[C-riggVA]

<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by Lyn O. Dyer &raquo;</TD></TR><TR><TD CLASS="quote">look on page 4 here.....http://ufpnet.com/PDF/Trailer%20Buddy%20Axle%20Maintenance.pdf..</TD></TR></TABLE>
Good info right there Helped me out today
Thanks