Results 1 to 4 of 4
  1. #1
    Member PowerFish's Avatar
    Join Date
    Jun 2004
    Location
    Gretna, NE
    Posts
    3,033

    '02 ZX250 Setup - 250 OX66

    Also posted on setups board;

    Soooo.... I'm at 3.25 below the pad, 27" Yamaha T1 prop, turning 5850rpm and GPS Speed best is 69.8, usually turning 5750-5800 at 68.x-69.x mph... Water pressure came up actually when I raised the plate last time, running 22+psi at WOT... 12" Slidemaster Plate, no spacers or wedges...

    According to the prop slip calculator, I'm running about 13% slip... Guys in my club were commenting on how high my rooster tail was last weekend...

    So, It would seem that I need to come up more on the plate, but would prefer to get close this time and fine tune from there...

    3.25" below seemed reasonable, but what is realistic for coming up, should I jump a 1/2", 3/4" or a full inch?

    Heartland of America
    2000 Ranger 520dvx
    2000 Mercury Optimax 225 - 0T136160
    --
    1997 Charger 395TF
    1997 Evinrude Vindicator 200 - G04296981 (E200STLEUB)



  2. Member
    Join Date
    Feb 2007
    Location
    Fulshear
    Posts
    144
    #2

    Re: '02 ZX250 Setup - 250 OX66 (Gamble.Bass)

    I think you could go to 2.5 and start going up a 1/4 inch at a time from there

  3. Member
    Join Date
    Dec 2006
    Location
    Acworth
    Posts
    2,128
    #3

    Re: '02 ZX250 Setup - 250 OX66 (DavidnTex)

    I've got the same boat/motor and am running a 27 tempest plus (I think thats the right one, it's the 3 blade one) and run about 70 fully loaded with a partner and livewells full. Running solo, I can get about 75.

  4. Member
    Join Date
    Jun 2004
    Location
    Collinsville, MS
    Posts
    5,792
    #4

    Re: '02 ZX250 Setup - 250 OX66 (pbmang)

    13% is pretty good. most goals are set to be at 10%. i bet your over-trimming with that high of tail. bump her own some to about 3/4 when WFO. should pick up some speed and loose a few rpms. I would also hang around the 3" below pad area unles you got to a different prop or have the current one worked

Similar Threads

  1. Skeeter sx176 with yamaha vmax 150 ox66 setup help
    By dedwards04 in forum Skeeter Boats
    Replies: 3
    Last Post: 08-11-2011, 09:24 AM
  2. Blazer Setup: 210 w/ 250 OX66
    By BassHog007 in forum Blazer Boats
    Replies: 5
    Last Post: 01-24-2011, 03:36 PM
  3. Please help with ZX250 Setup w/ yamaha 300
    By Willyjoe0118 in forum Skeeter Boats
    Replies: 14
    Last Post: 09-27-2009, 05:00 PM
  4. ZX250 setup question
    By Neilslure in forum Skeeter Boats
    Replies: 5
    Last Post: 03-24-2008, 01:07 PM
  5. SET UP HELP ZX250 / VMAX 250 OX66
    By DELMARVA DAVE in forum Skeeter Boats
    Replies: 6
    Last Post: 07-04-2006, 08:31 AM