Post pics of your tin

[jc1234]

I thought it was time to introduce myself to the tin boat forum members. Here is my tin. A 2007 Lowe Stinger ST170 with a 2009 75 Mercury Optimax. Been reading this forum for about a year now and have learned a lot from you guys. The members in this tin forum are the most civil to each other. I hope to contribute at some point.

[IMG][/IMG]

Very nice looking ride. I'm probably like you in that I don't contribute much but have learned a lot from these fine people here.

[krr6581]

I always did like this boat from Tracker. Too bad they stopped making it. For info I was actually trying to post this on the White Tracker Avalanche that was shown 5 or 6 pages earlier. I meant this to go with the picture of the Tracker Avalanche.

[basscatcher89]

You playing on buying a blind or building?? I am still on the fence on which route I want to take.

I think I'm going to build one. Havent seen any that would fit well on my boat. I just need to build some sides and then I'm going to put my layout blind that I use for field hunting geese up on the front deck. I can fit 3 layout blinds between the front and back deck and one guy can sit down by the console without one so I'm figuring I can hunt 4 no problem but will normally hunt 2 and occasionaly 3.

[mrc.in.wi]

'07 Triton VT19 115 Evinrude Etec
Recessed foot pedal
Bluewater LED Pro boat package
Minn Kota Maxxum 75 lb

whats the performance numbers on this rig??????

[mrc.in.wi]

Well ran out to the lake today to check on the Mark 4 I installed at 2 AM this morning to make sure she worked. The boat came with the X-4 pro and I used the same transducer and wanted to verify proper operation. The Mark 4 has built in GPS which I use for the speedo, bank beater not needing much in the depth dept. This will allow me to remove the speedometer and install something like the PRV-15 head unit for some tunes. Took some shots while I wasAttachment 103592Attachment 103593Attachment 103594Attachment 103595Attachment 103596 out.

this one too....whats the performance numbers??????

[justsomeguy]

this one too....whats the performance numbers??????

With me alone, 265#, and half a tank with the 19" BRP aluminum at 51-5200 rpm hit a new high 47.2 gps.

[mrc.in.wi]

With me alone, 265#, and half a tank with the 19" BRP aluminum at 51-5200 rpm hit a new high 47.2 gps.

Nice......good looking rig

[TritonTRXV8]

With me alone, 265#, and half a tank with the 19" BRP aluminum at 51-5200 rpm hit a new high 47.2 gps.

Your engine is still very new with low hours. It will loosen up and run better. Should wind a little tighter after the first 20-30 hours.

[jeff_3272]

With me alone, 265#, and half a tank with the 19" BRP aluminum at 51-5200 rpm hit a new high 47.2 gps.

You need to look into getting a different prop and/or raising your motor up on the transom. Should be running 5500-6000 rpm's.

[TritonTRXV8]

With me alone, 265#, and half a tank with the 19" BRP aluminum at 51-5200 rpm hit a new high 47.2 gps.

Wonder if your tach is off a little. With the 2.0:1 gearcase and a 19p prop your theoretical speed at 5200 rpm is 46.7 mph. And thats with 0% prop slip. To get 47 with that prop you would have to be turning at least 5500 rpm.

[justsomeguy]

You need to look into getting a different prop and/or raising your motor up on the transom. Should be running 5500-6000 rpm's.

I had a 17" Power Tech prop which I didn't like so I sold it, it turned 5700 but was slow only could muster 43.5. In the market for a 18" Raker, hopefully will have full funding by end of month. It was unseasonably cool that morning at 51, plus a good chop and little tail wind but it was moving so I marked it...

[justsomeguy]

Wonder if your tach is off a little. With the 2.0:1 gearcase and a 19p prop your theoretical speed at 5200 rpm is 46.7 mph. And thats with 0% prop slip. To get 47 with that prop you would have to be turning at least 5500 rpm.

Possible I assume, factory tach, also want to get the I command tach which gets the info straight from the EMM as well as other readings like engine hours etc, like your Merc monitor. At $364 just for the unit the prop is first on the list, I command next, who knows maybe, just maybe by then I will be ready for your personal favorite.......JP but as of now I'm still on the fence, and I have the wife to contend with, she thinks she knows something.

[TritonTRXV8]

Possible I assume, factory tach, also want to get the I command tach which gets the info straight from the EMM as well as other readings like engine hours etc, like your Merc monitor. At $364 just for the unit the prop is first on the list, I command next, who knows maybe, just maybe by then I will be ready for your personal favorite.......JP but as of now I'm still on the fence, and I have the wife to contend with, she thinks she knows something.

That will be really nice. Nothing like getting that vital info straight from the computer. Factory tachs being a little off is very common. Mine is off 150 rpm compared to smartcraft. I would personally recommend getting the command link first. The more accurate info you have the better you will be able to dial everything in for selecting the right prop.

[USC Woodie]

Here's my 2014 rig!

IMG_1183.jpg

[Ship]

Very nice Woodie.

[TritonTRXV8]

Yea it is. Very sharp.

[bettis36]

[bettis36]

[TritonTRXV8]

Very nice Tracker!

[bettis36]

Thanks