Results 1 to 8 of 8
  1. #1
    Member
    Join Date
    Dec 2005
    Location
    Somewhere on Smith Mountain Lake
    Posts
    164

    Trim problem......need professional input

    I'm having trouble with my trim "up" only working intermittently.Once it is not raising the motor,I can tap on the trim junction box and it starts to work again.I've looked everything over and didnt notice anything loose or out of place.Any ideas of what may be happening or is the trim box wiring going bad?It doesnt happen all the time but enough that I have to do something about it.

    Note: I never have any trouble with trimming "down",it has never acted up,not once.

    Motor is E200STLENS


  2. RIP Evinrude 1907-2020 JR19's Avatar
    Join Date
    Feb 2005
    Location
    Columbia, KY
    Posts
    13,495
    #2

    Re: Trim problem......need professional input (5basslimit)

    Sounds like you have a trim relay going bad. Switch the up relay with the down relay and if you have a problem going down then you need a new relay. I think a new relay is around $14 that would be a cheap fix. Hope you do not have the problem I had. My trim would act up and my problem was where the trim wires hook into the power distribution panel. The male end of the plug was broke loose and I had to get a new panel. If my memory is correct a new power distribution panel set me back around $250-$300 installed but your problem sounds more like a relay since it only happens in the up mode. My problem was up and down some times it would work some times it would not do anything because of the bad connection in the panel. Try changing the relays it is not uncommon for them to go bad.

    JR19

  3. RIP Evinrude 1907-2020 JR19's Avatar
    Join Date
    Feb 2005
    Location
    Columbia, KY
    Posts
    13,495
    #3

    Re: Trim problem......need professional input (JR19)

    After re reading your post I see you asked for professional input...well I am just a backyard mechanic but I did sleep at a Holiday Inn express last night One of the Evinrude gurus will be along to help you out ...I bet they have you to check the relays

    JR19

  4. Member
    Join Date
    Dec 2005
    Location
    Shepherdstown, WV
    Posts
    6,145
    #4

    Re: Trim problem......need professional input (JR19)

    Mine did the same thing, except it wouldnt move up at all. THe motor would turn, but only go down. Turned out it was a valve inside the unit stuck. Took just the trim motor to a mechanic, and it turned out to be $20 to fix it, since he didnt have to remove the motor from the boat.

    But I would check your relay first.
    2022 Hog Island Skiff
    Johnson 70/40 jet

    1992 Champion 184
    1992 Evinrude Intruder 150 hp

    Bouncin' off rocks, and catching the smallies.

    Potomac River Smallmouth Guide

    Owner of Potomac Custom Tackle

  5. SC Club Moderator ChampioNman's Avatar
    Join Date
    May 2004
    Location
    Crawfordville, FL/Lake Hartwell, SC
    Posts
    72,198
    #5

    Re: Trim problem......need professional input (JoshKeller)

    Yep, swap the relays around and see if it follows.

  6. Member
    Join Date
    Dec 2005
    Location
    Somewhere on Smith Mountain Lake
    Posts
    164
    #6

    Re: Trim problem......need professional input (ChampioNman)

    Thanks for the replies....hopefully it's a quick and cheap fix.

  7. SC Club Moderator ChampioNman's Avatar
    Join Date
    May 2004
    Location
    Crawfordville, FL/Lake Hartwell, SC
    Posts
    72,198
    #7

    Re: Trim problem......need professional input (5basslimit)

    About $12.00 for the relay, See you on KY lake.

  8. Member
    Join Date
    Jun 2005
    Location
    Ottawa
    Posts
    449
    #8

    Re: Trim problem......need professional input (ChampioNman)

    Change both relays while your there.

Similar Threads

  1. Professional "Prop" Waxing now available!
    By KissMyBass in forum Kentucky Fishing
    Replies: 14
    Last Post: 09-22-2010, 11:37 AM
  2. tach problem need input???
    By twitch in forum Evinrude/Johnson Motors
    Replies: 1
    Last Post: 06-21-2010, 05:57 AM
  3. TRim Problem/Manual TRim
    By Nick_Barr in forum Evinrude/Johnson Motors
    Replies: 2
    Last Post: 05-30-2010, 08:18 AM
  4. Trim problem......need professional input
    By Gambler250XB in forum Evinrude/Johnson Motors
    Replies: 8
    Last Post: 08-11-2005, 05:55 PM
  5. 1985 Johnson 150 GT, Problem in detail, any input would be greatly appreciated
    By flametamer123 in forum Evinrude/Johnson Motors
    Replies: 2
    Last Post: 06-04-2005, 05:23 PM