Results 1 to 5 of 5
  1. #1
    Member
    Join Date
    Jun 2008
    Location
    Marengo
    Posts
    14

    1993 ProCraft hull crack repair

    I have a 1.5-2 inch crack in the hull below the water line. It has cracked the gelcoat and paint, but does not appear to go all the way through. Can this be repaired from the outside with a kit or something. I don't really want to disassemble the entire boat for just this crack.

    It also appears they may have beached the front of the boat and it has warn away the gelcoat and paint on the bow (about 2 feet by 1/4-1/2 inch wide).
    A bad day fishing is always better than a good day at work!!!

  2. Moderator unklenew's Avatar
    Join Date
    Jul 2007
    Location
    Collierville, Tennessee
    Posts
    11,141
    #2

    Re: 1993 ProCraft hull crack repair (Landshark)

    Some pics would help a lot. For the bow just get a Keel Shield to cover the worn area.

    JimAndy Turner
    02 Procraft 210 Super Pro
    02 Mercury 225 EFI
    "After Darkness Light"

  3. Member delee36's Avatar
    Join Date
    Jul 2007
    Location
    Hammond, IN.
    Posts
    11,037
    #3

    Re: 1993 ProCraft hull crack repair (Landshark)

    the crack will need to be "grounded" out...ground down to good glass that is not cracked...then cross ground to the same depth at each end of the crack...then tapered back, then filled, patched and painted.
    not a small job
    being on the bottom I might take it in and have it done...one of those things where you just want to be sure it is done well and done right...not like patching a topside crack.

    in fact a marina will probably cut out the bad area and replace it.

  4. Member
    Join Date
    Jun 2008
    Location
    Marengo
    Posts
    14
    #4

    Re: 1993 ProCraft hull crack repair (delee36)

    Here are some photos, although they are not the best you can see some of the detail. It is about a 1.5-2 inch crack on one of the ribs in the bow. It appears it to a shot from a stick up or the like. I'll try for some better photos tomorrow.

    I'll also get a photo of the rubbed off gel coat on the V bottom.
    http://s319.photobucket.com/al...Crack/
    A bad day fishing is always better than a good day at work!!!

  5. Moderator unklenew's Avatar
    Join Date
    Jul 2007
    Location
    Collierville, Tennessee
    Posts
    11,141
    #5

    Re: 1993 ProCraft hull crack repair (Landshark)

    After looking at the pictures you might be able to get away with Marine Tex. Most boat supply stores carry it.

    JimAndy Turner
    02 Procraft 210 Super Pro
    02 Mercury 225 EFI
    "After Darkness Light"

Similar Threads

  1. 1993 Procraft Restore
    By reelnmn in forum Bassboat Restoration
    Replies: 8
    Last Post: 01-28-2012, 06:43 PM
  2. Crack repair
    By 85 kingfisher in forum Bassboat Restoration
    Replies: 5
    Last Post: 05-03-2009, 01:04 PM
  3. Spider Crack on my hull
    By MetsFan9 in forum Skeeter Boats
    Replies: 4
    Last Post: 02-22-2009, 03:24 PM
  4. 22" crack in the hull
    By bamdad04 in forum Bullet Boats
    Replies: 9
    Last Post: 10-27-2008, 03:45 PM
  5. crack in hull
    By manskeeto in forum Bassboat Restoration
    Replies: 3
    Last Post: 11-08-2005, 01:09 PM