Results 1 to 10 of 10

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Member basscatlildave's Avatar
    Join Date
    Mar 2005
    Location
    Robertsdale AL
    Posts
    11,145

    Factory Transducer

    My 22 Eyra has a 15 inch Hummingbird on the console with the transducer mounted on the jack plate. Even at low speeds it doesn’t read depth. Will the factory transducer in the bilge hook up and work at speed?

  2. Member
    Join Date
    Jun 2004
    Location
    Baytown Texas
    Posts
    1,114
    #2
    The transducer in the bilge (if you have one) should already be connected to your unit through a Y cable. Yes it should read. Maybe it has never been connected or maybe it is bad. Does SI and DI work appropriately?

  3. Member basscatlildave's Avatar
    Join Date
    Mar 2005
    Location
    Robertsdale AL
    Posts
    11,145
    #3
    Yes DI and SI are working fine. I never thought about the one in the bilge until my buddy said something about it.
    Quote Originally Posted by Phil Addison View Post
    The transducer in the bilge (if you have one) should already be connected to your unit through a Y cable. Yes it should read. Maybe it has never been connected or maybe it is bad. Does SI and DI work appropriately?

  4. Member basscatlildave's Avatar
    Join Date
    Mar 2005
    Location
    Robertsdale AL
    Posts
    11,145
    #4
    I looked last night night and under the hoses it looks more like a cup with no wires going to it. I don't know why someone would have cut the cable going to it and don't see where it has been cut. Did BassCat install a cup or something to put a transducer in?

  5. BBC SPONSOR Bass Cat Boats's Avatar
    Join Date
    Jul 2004
    Location
    Mountain Home
    Posts
    16,128
    #5
    That should be a standard “puck” style transducer.

  6. Member basscatlildave's Avatar
    Join Date
    Mar 2005
    Location
    Robertsdale AL
    Posts
    11,145
    #6
    I will move the hose tonight and report back tomorrow. There looks like enough room to epoxy another one down close to it if that will be easier that digging this one out.
    Quote Originally Posted by Bass Cat Boats View Post
    That should be a standard “puck” style transducer.

  7. Member basscatlildave's Avatar
    Join Date
    Mar 2005
    Location
    Robertsdale AL
    Posts
    11,145
    #7
    It's definitely a Lowrance style transducer down there. Either some one cut or just pulled out the wires out of it. My question is how hard is it to get the puck out or there seems enough room to just glue down another one beside it?

  8. Member apdriver's Avatar
    Join Date
    Feb 2013
    Location
    Bryant, AR
    Posts
    1,077
    #8
    It shouldn’t be hard. Last one I did, I put the end of a 2x4 against it and gave it a firm tap with a hammer. Before you go back with one, you should prep that area. There is also a transducer epoxy that all the electronics mfgs use. West Marine has the Lowrance stuff in stock.
    2013 BassCat Cougar
    Serial # 1B962763

  9. Member basscatlildave's Avatar
    Join Date
    Mar 2005
    Location
    Robertsdale AL
    Posts
    11,145
    #9
    It definitely had a Lowrance style puck with no wires in it. Since I have a H-Bird on the console should I put a H-Bird style back or use the one like it came factory with?

  10. Member
    Join Date
    May 2014
    Location
    Albany, NY
    Posts
    793
    #10
    Put a Humminbird one in
    2020 Triton 21TRX Patriot Elite, Mercury 250 Pro XS (2B687844)
    1999 Champion 193, Mercury 200 EFI (0T333415)