TRITON TOUCH PADS OR CONVERSION KITS

[The Parts Mom / Carol]

12/11/2020 UPDATE
I have received a new supply of the oval touch pads and the conversion kits. Please give me a call if you need these.

Most of the older Triton touch pads are no longer available thru 2014. There are conversion kits available for all of them. Prior to late 2010, all of the kits are plug and play. From late 2010 thru 2014 you are looking at rewiring the boats but the kits contain the wiring harness. I have the conversion kits in stock at less than factory pricing. Let me know what you need and I will price them for you thru PMs or emails, please. If you call, please ask for me, 615-797-4760

***** I have been informed I can still get the oval touch pads. *****

candoparts@yahoo.com
Thank you!!!
Carol Newnum
The Parts Mom
C&O Marine Parts Department

[jbh3]

Thank you for this information, Carol. You folks do a great job out there.

Mod's, it wouldn't hurt to add this to the sticky's above. There are a lot of us that have the potential to need these parts.

[The Parts Mom / Carol]

Thank you jbh3!! I try to keep y'all on the water to the best of my ability. All of your continued support and business is greatly appreciated!!!!!

[96MrBass]

Do you possibly have any of the 05 style touch pads?

[The Parts Mom / Carol]

Do you possibly have any of the 05 style touch pads?

So you just need one side and if so, which side?

[96MrBass]

Actually interested in both sides livewell side and master power if you have them.

[The Parts Mom / Carol]

Actually interested in both sides livewell side and master power if you have them.

I do have one of each here at this time and the vendor has informed me I can still get them. You can call me at 615-797-4760 to place an order. I have these 2 pulled and tucked away for you.

[The Parts Mom / Carol]

Actually interested in both sides livewell side and master power if you have them.

These are back in stock. Call me at 615-797-4760 and ask for Carol.
Thanks!!!

[The Parts Mom / Carol]

I have these in stock again if you are still needing them. I have both of the touch pads and the conversion kits.

[Gagoodnight]

I have a 2012 20xs elite and the push button pad stopped working can anyone point me in the direction of a conversion kit from push button to rotary please I have been dealing with this problem for a while and nobody has been able to help me so far including Triton and it is very frustrating. Thanks.

[The Parts Mom / Carol]

For the 2012 I need to know where your PME (brain box) is located. If it is in the bilge area, I am currently out of stock for the conversion kit. I do have them on order. I need to contact my vendor again tomorrow to see if they can tell me when I will be getting these. If you would like to send me a PM with your name and your phone number, I will put you on the list to reserve one for you.
Thanks!!
Carol Newnum

[mudman3151]

What is the turn around time on getting the conversion kit? I have a 2012 also and my box is in the bilge area.

[Bennie Tarleton]

I have a 2012 21 hp elite did you have any luck finding any help on touch pads.All mine quit today the start pad quit several years back
Thanks
Bennie Tarleton

[trol20x]

Hey

Do you have original touch pads for 2006 model both sides .Would like to buy them and save them for future just in case .

[The Parts Mom / Carol]

Hey

Do you have original touch pads for 2006 model both sides .Would like to buy them and save them for future just in case .

I finally got a chance to go look for these. I even checked my stash (sssshhhhh!!!). The only ones I have left are 2 of the power side. These are no longer available for me to order. You will need to get the conversion kit.

[TillerHandle]

!Hey guys, I purchased one of these kits from Carol. I had a touchpad dash that gave me nightmares. Carol contacted the manufacturer of my touch pad system and they said to convert to the rotary switches would mean a complete rewire, because they did not have a conversion kit for a 2015 model. After some thought, I contacted Carol and told her I had a plan to make these rotary switches work on my rig. I ordered the switches and harness and here is what I did to convert it: 1) removed the touchpad system & brain 2) Clipped all existing wires to box lights, bilges, pumps, anchor & navigation lights. Clip the just behind the gear lever control. 3) Identify each wire by putting 12V to it and see what comes on & label the wire. 4) install the new switches & harness. 5) Clip the wires from the new harness at the 40 pin connector (Carol supplied a schematic of what each wire went to on the dash) 6) match the wires from the connector to those you've labeled from the old system, use solder & butt connectors to connect the two ends.

It worked perfectly! You will give up livewell controls at the bow & you'll have to purchase the bow panel that has the oval switch panel as opposed to the rectangular switch panel, but you still have your anchor light control & trim control at the bow with the new panel. Wiring time was about 12 hours and I'm not a wiring guru, but I now have a much more dependable system! Give Carol a call!!!

[The Parts Mom / Carol]

!Hey guys, I purchased one of these kits from Carol. I had a touchpad dash that gave me nightmares. Carol contacted the manufacturer of my touch pad system and they said to convert to the rotary switches would mean a complete rewire, because they did not have a conversion kit for a 2015 model. After some thought, I contacted Carol and told her I had a plan to make these rotary switches work on my rig. I ordered the switches and harness and here is what I did to convert it: 1) removed the touchpad system & brain 2) Clipped all existing wires to box lights, bilges, pumps, anchor & navigation lights. Clip the just behind the gear lever control. 3) Identify each wire by putting 12V to it and see what comes on & label the wire. 4) install the new switches & harness. 5) Clip the wires from the new harness at the 40 pin connector (Carol supplied a schematic of what each wire went to on the dash) 6) match the wires from the connector to those you've labeled from the old system, use solder & butt connectors to connect the two ends.

It worked perfectly! You will give up livewell controls at the bow & you'll have to purchase the bow panel that has the oval switch panel as opposed to the rectangular switch panel, but you still have your anchor light control & trim control at the bow with the new panel. Wiring time was about 12 hours and I'm not a wiring guru, but I now have a much more dependable system! Give Carol a call!!!

Thank you for posting the process that you had to go thru to make this work for you. Maybe they will put together a conversion kit for them soon. I don't understand why they continue to install touch pads in the boats!! I don't think there is a boat brand out there that has not had issues with them.

[The Parts Mom / Carol]

Hey

Do you have original touch pads for 2006 model both sides .Would like to buy them and save them for future just in case .

I'm pretty sure they are the oval style touch pads. You can call me to put in an order for them. I have one set in stock at the moment but more on order. If 96MrBass doesn't get them, they are yours and if he does, you will be 1st on the list for the new order. 615-797-4760 and ask for Carol.

[The Parts Mom / Carol]

Hey

Do you have original touch pads for 2006 model both sides .Would like to buy them and save them for future just in case .

Don't know if you saw my update for the original post. The vendor said I can still order the oval touch pads if you are still interested in getting a set.

[The Parts Mom / Carol]

Hey

Do you have original touch pads for 2006 model both sides .Would like to buy them and save them for future just in case .

I got some of these in if you still need them. I have the conversion kits also.