How long is YOUR rig??

[AWilliams]

So, I'm starting to look at getting a used tin boat next year. Maybe a G3, Tracker, Triton etc... This will be my first boat and would like to know what the over all length of some of these tin boats are. I have limited room on the side of my house so....let'er rip. Let me know what you you have and the overall length and width with the motor.

I know some of these have a folding tongue so folded length with motor and outside of wheel fenders is what I'm looking for.
Thanks

[B.R.ONE]

My tin boat is a 16ft. v-bottom, about 4to5 ft. wide at he widest part of the front. The trailer is about 17.5 ft. long and fits in my garage very nice. I fish the Ohio River, Ky. Lake, Lake Barkley most. The old boat does pretty well in the big water, don't do it fast but gets me there and back.

[SpeckTracker]

Mine is a Tracker PT190 and its about 22 feet long and about 9 or 10 feet wide. It is one of the bigger tins excluding the big Xpress's

[AWilliams]

Thanks guys...keep em' coming.
AW

[Dave 620VS]

I have a 2004 17ft polar kraft deep V, great boat still, take it on large lakes like ozarks, vermilion (MN) with no problems, just make sure you get enough hp on em

[Trent_in_BG]

Mine has a 90" beam so on trailer somewhere around 9' I would guess. Boat is 20' long plus 6" jack plate plus motor and then add a couple of feet for the tongue. I would huess aroung 25' or so. I really never measured it because I rent a storage unit for it. That's something you could always do if they are available close to you or your favorite lake.

[Bub]

my boat is a 17.5' rig however on the trailer with motor trimmed down it would require a 24' garage if you wanted to close the garage door. I don't have the break away tongue though, that would help tremendously!

[spec]

Fisher Marine Pro Hawk 170 with 90 Opti. 88 inches wide and 20 feet 4 inches long with motor down and tongue swung "in".

[kk4iz]

Xpress X21TS just a little over 21 feet and boat and trailer just over 27 feet.

[Musky Tom]

Got a Lowe 165 Fishing Machine two years ago

16ft 5in length
82" beam
42" length livewell
Max hp 75
20' 8" length on trailer...swingaway trailer tongue

Tom

[DJBass]

Mine is 2011 20 ft long and 94 inch beam its an Alumacraft mv 2072 all welded with a side console
Mercury Optimax 115
Minnkota fortrex 101
Hydraulic jack plate too!

With trailer and motor its around 25 to 26 long and
about 9 ft wide

[Les Young]

1998 Xpress H-56 with 98 Mariner 135. 18'3" in length. Don't remember with for sure, but it is very wide & stable. Runs 58 gps with a very heavy tourney load full on gas with 2 anglers & rides great. Look at Xpress before you make your mind up on aluminium boats as you may like them very much for sure.

[dblume]

12"

[BareZ518]

17.5, easily fits in g-rage

[Sixty Minutes]

18 ft Lund Pro VSE. 96" beam at the transom. It must be a bit wider than 9 ft. The tires are almost on the center line and on the white stripe on the berm on the country roads. I would guess 25' long on the trailer. I use that folding tongue every time I put it in the driveway. Very handy feature of the trailer.

[tcesni]

Triton 176 Mag (17' 6") just fits in 24 foot garage without a swing away tongue.