Results 1 to 7 of 7
  1. #1
    Member
    Join Date
    Sep 2005
    Location
    HUTTO TEXAS
    Posts
    86

    specific engine type

    I have a 1985 johnson 150 gt. model #j150stlcos. is this a 60 degree v engine.

    I am going to install a water pressure guage and if the instuctions are correct I need to
    install an elbow on the port head at the water pressure plug. is this plug at the top or bottom of the engine and what would be the details of its descripion? the instructions are only good if this a 60 degree v engine.
    John Carmody

    Georgetown Texas

    1984 Starfire FS 160 Johnson 150gt
    2017 ZX190 Yamaha 150 SHO

  2. Member
    Join Date
    Apr 2005
    Location
    Rio de Janeiro
    Posts
    165
    #2

    Re: specific engine type (sk1984sf)

    Nope,this is not a 60 o. Engine ,they started in 1991

    This is my backyard
    This is the new fence!!
    http://s168.photobucket.com/al...3.flv
    The other side!
    http://i168.photobucket.com/al...9.jpg

  3. Member
    Join Date
    Sep 2005
    Location
    HUTTO TEXAS
    Posts
    86
    #3

    Re: specific engine type (jorgeparagon)

    thank you sir, so what is the best installation for my engine water pressure guage?
    John Carmody

    Georgetown Texas

    1984 Starfire FS 160 Johnson 150gt
    2017 ZX190 Yamaha 150 SHO

  4. Member
    Join Date
    Apr 2005
    Location
    Rio de Janeiro
    Posts
    165
    #4

    Re: specific engine type (sk1984sf)


    This is my backyard
    This is the new fence!!
    http://s168.photobucket.com/al...3.flv
    The other side!
    http://i168.photobucket.com/al...9.jpg

  5. Member
    Join Date
    Sep 2005
    Location
    HUTTO TEXAS
    Posts
    86
    #5

    Re: specific engine type (jorgeparagon)

    does it need to be a tee fitting so the water still discharges or an elbow straight to the guage?


    Modified by sk1984sf at 2:23 PM 4/27/2007
    John Carmody

    Georgetown Texas

    1984 Starfire FS 160 Johnson 150gt
    2017 ZX190 Yamaha 150 SHO

  6. SC Club Moderator ChampioNman's Avatar
    Join Date
    May 2004
    Location
    Crawfordville, FL/Lake Hartwell, SC
    Posts
    72,181
    #6

    Re: specific engine type (sk1984sf)

    You have a flat back motor on the bottom STBD side where the tell tale hose goes out install a T there, run the hose up through the PORT side access where the Electical wires go through, If you are brave and have skills with a drill, you can drill a hole in the controll cable lower motor grommet on the STBD side.

  7. Member
    Join Date
    Sep 2005
    Location
    HUTTO TEXAS
    Posts
    86
    #7

    Re: specific engine type (ChampioNman)

    thank you for your help, again.
    John Carmody

    Georgetown Texas

    1984 Starfire FS 160 Johnson 150gt
    2017 ZX190 Yamaha 150 SHO

Similar Threads

  1. Looking for a specific hook
    By FastBug250 in forum Rod Building & Tackle Making
    Replies: 5
    Last Post: 01-06-2013, 12:21 PM
  2. Looking for a specific skirt tab
    By MDisbrow in forum Rod Building & Tackle Making
    Replies: 9
    Last Post: 03-08-2012, 05:54 PM
  3. Need specific jigheads....help!
    By Gambler250XB in forum Rod Building & Tackle Making
    Replies: 6
    Last Post: 04-17-2007, 04:47 AM
  4. How to Decarb this specific engine (GT150)
    By Stut in forum Evinrude/Johnson Motors
    Replies: 7
    Last Post: 04-11-2007, 08:11 AM
  5. Anyone specific to contact at BRP?
    By omcparts in forum Evinrude/Johnson Motors
    Replies: 1
    Last Post: 07-31-2006, 01:54 PM