Thread: need help

Results 1 to 12 of 12
  1. #1
    Member
    Join Date
    Jul 2009
    Location
    Bayou Chicot
    Posts
    2,498

    need help

    ok i spun the bushin out of my prop today, i thought i got the lower unit but that looks ok my 2 questions are..... 1- the outer shaft seal is blown and leaking oil, is this a seal that i can change myself from the outside of the motor without tearing it open, 2- i have a spare prop but doesnt seem to fit right when i tighten it down it gets very stiff and will not free spin do i need a different thrust washer on the back? also where can i find the differnt front thrust washers all of my props have a different stlye of lock down


    Kevin Soileau
    2007 21 xdc
    250 xs

  2. Team Geritol RogerR's Avatar
    Join Date
    Mar 2005
    Location
    French Settlement La.
    Posts
    19,619
    #2

    Re: need help (dirtdemon)

    I can't help but Doug or Jason should be able too.

  3. Member
    Join Date
    May 2007
    Location
    LIVINGSTON, Louisiana
    Posts
    22,636
    #3

    Re: need help (dirtdemon)

    what kind of motor is it? what kind of props??????????

  4. Member
    Join Date
    Jul 2009
    Location
    Bayou Chicot
    Posts
    2,498
    #4

    Re: need help (DOUGMCGEE188)

    1996 marinier 225 super mag w/ bobs low water pickup. i spun the hub out of my 27 tempest, i have a 26 hoss to put on it the hoss touches when i tighten up and has diffrent front side than the tempest


    Kevin Soileau
    2007 21 xdc
    250 xs

  5. Member
    Join Date
    May 2007
    Location
    LIVINGSTON, Louisiana
    Posts
    22,636
    #5

    Re: need help (dirtdemon)

    needs a different thrust washer than the tempest. Not sure which one or where to get one for it. you dont have the flo torques in the tempest? If so just take out the delrin sleeve and pop in another one. if not you'll have to get one pressed in. Should be able to change the seal from outside. usually last thing they put on anyway.

  6. Member
    Join Date
    Jul 2009
    Location
    Bayou Chicot
    Posts
    2,498
    #6

    Re: need help (DOUGMCGEE188)

    thats kinda what i thought about the seal, red river marine said the whole bearing carrier had to come out two change it because there is two seals.

    <TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by DOUGMCGEE188 &raquo;</TD></TR><TR><TD CLASS="quote">needs a different thrust washer than the tempest. Not sure which one or where to get one for it. you dont have the flo torques in the tempest? If so just take out the delrin sleeve and pop in another one. if not you'll have to get one pressed in. Should be able to change the seal from outside. usually last thing they put on anyway.</TD></TR></TABLE>
    what is flo torques doug not sure what your talkin bout


    Kevin Soileau
    2007 21 xdc
    250 xs

  7. Member Gun Runner's Avatar
    Join Date
    Mar 2008
    Location
    Denham Springs Louisiana
    Posts
    15,775
    #7

    Re: need help (dirtdemon)

    The flo torque is the type of hub that mercury runs inside their props . But since you spun the hub in that temp. prop I wouldnt think that youll beable to reuse the derlin sleeve out of it ( the derlin sleeve is the black plastic insert that goes into the back side of your prop) .


    Modified by Gun Runner at 5:44 PM 8/8/2009
    BassCat-illac
    FastCat Fishin Team
    If you aint first , your last !!!
    All fat girls welcomed !!!!!

  8. Team Geritol RogerR's Avatar
    Join Date
    Mar 2005
    Location
    French Settlement La.
    Posts
    19,619
    #8

    Re: need help (Gun Runner)

    Hey Gun you getting like Doug, knowing all that $hit. Breaking down must help teach you stuff.

  9. Member Gun Runner's Avatar
    Join Date
    Mar 2008
    Location
    Denham Springs Louisiana
    Posts
    15,775
    #9

    Re: need help (RogerR)

    <TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by RogerR &raquo;</TD></TR><TR><TD CLASS="quote">Hey Gun you getting like Doug, knowing all that $hit. Breaking down must help teach you stuff. </TD></TR></TABLE>Ya , I guess that after you tear up enough stuff and spend enough money fixin it your bound to learn something .
    BassCat-illac
    FastCat Fishin Team
    If you aint first , your last !!!
    All fat girls welcomed !!!!!

  10. Member
    Join Date
    Jul 2009
    Location
    Bayou Chicot
    Posts
    2,498
    #10

    Re: need help (Gun Runner)

    thnx guys for all the info well at least i learned a little sumtin


    Kevin Soileau
    2007 21 xdc
    250 xs

  11. Member
    Join Date
    May 2007
    Location
    LIVINGSTON, Louisiana
    Posts
    22,636
    #11

    Re: need help (RogerR)

    <TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by RogerR &raquo;</TD></TR><TR><TD CLASS="quote">Hey Gun you getting like Doug, knowing all that $hit. Breaking down must help teach you stuff. </TD></TR></TABLE>

    Hell yeah i have owned 7 mercs so i had to learn to work on them!

  12. Member Gun Runner's Avatar
    Join Date
    Mar 2008
    Location
    Denham Springs Louisiana
    Posts
    15,775
    #12

    Re: need help (DOUGMCGEE188)

    I done had 2 , worked on one all the time and never on the other one .


    Modified by Gun Runner at 7:07 PM 8/9/2009
    BassCat-illac
    FastCat Fishin Team
    If you aint first , your last !!!
    All fat girls welcomed !!!!!