Results 1 to 13 of 13
  1. #1
    Member
    Join Date
    Apr 2007
    Location
    Visalia, CA
    Posts
    497

    pedestal removal

    I have a ranger 392V. The rear folddown seat pedestal will not come out of the hole. I am not sure it has ever been out. Any ideas on how to remove?

    Thanks

  2. Member
    Join Date
    Nov 2008
    Location
    Glasgow
    Posts
    742
    #2

    Re: pedestal removal (wassupc)

    24" Rigid aluminum pipe wrench

  3. Member crimsonpride40's Avatar
    Join Date
    Jan 2009
    Location
    Bagley, AL
    Posts
    617
    #3

    Re: pedestal removal (javelin377)

    Use a strap wrench and a litte penetrating lube. The strap wrench will keep you from scratching your pedestal. The rubber strap also gets a really good bite to let you generate some torque.
    Matthew 28:20
    teaching them to observe all things whatsoever I commanded you: and lo, I am with you always, even unto the end of the world.

  4. Member
    Join Date
    Feb 2008
    Location
    joppa
    Posts
    179
    #4

    Re: pedestal removal (wassupc)

    Same thing happened to me 3 yrs. ago. Left front pedestal seat in rear over winter, garaged. Metal fused together. Ended up having to drill it out! Pipe wrench, hammer, wd-40, etc., would not budge. Best of luck.

  5. Member
    Join Date
    Feb 2007
    Location
    st louis
    Posts
    42
    #5

    Re: pedestal removal (wassupc)

    Instead of scratching it all up with a wrench Drill3/8 hole inseart a bolt and put a floor jack under under the bolt it will come right out lube first, put a rubber plug in hole



    Don Ellsworth
    St louis Mo
    3mm Lake Of The Ozarks
    1996 896 175 merc


  6. Member cosmoranger's Avatar
    Join Date
    May 2007
    Location
    Marion, Illinois
    Posts
    1,245
    #6

    Re: pedestal removal (wassupc)

    Keep Bass Boat Saver or any other detail wax on them and the will come out a lot easier!!!

  7. Member dchance's Avatar
    Join Date
    Jan 2006
    Location
    Rolla, MO
    Posts
    9,816
    #7

    Re: pedestal removal (wassupc)

    Just had the same thing happen with my front one. Had to use a pipe wrench to get it off. Tore it up a little bit but I got it out. then I used a dremel with a sanding bit to sand out a tad of the post hole in the boat. works great now.

    Derek Chance
    2021 Nitro Z19 Pro 200 Mercury ProXs
    BTS and KVD Line and Lure


  8. Member Hoover's Avatar
    Join Date
    Jun 2006
    Location
    Rochester Hills Michigan
    Posts
    418
    #8

    Re: pedestal removal (dchance)

    The thing I found to work once you got it out was a brake caliper hone or a wheel cylinder hone...(keeps the hole round) once your finished put some silcone spray on the plastic insert...

  9. Member
    Join Date
    Jul 2008
    Location
    Eleroy, IL
    Posts
    197
    #9

    Re: pedestal removal (Hoover)

    I had that problem. After I got them out, heard about this as a solution. Use parafin wax on the seat base. Won't stain anything, cheap, easy, and protects the surface of the metal as well.
    '99 Triton SF 21 -- 2014 225 ProXS

  10. Member rkabusa's Avatar
    Join Date
    Jan 2009
    Location
    Fort Worth, TX
    Posts
    366
    #10

    Re: pedestal removal (Triton SF21)

    the champion that i just bought had a stuck back seat i tried the pipe wrench with a five foot breaker bar just to turn it.then broke out the engine hoist wrap a chain around the pole ,add a little pressure and turn with pipe wrench and the seat goes flying

  11. Member
    Join Date
    Feb 2007
    Location
    NW Houston
    Posts
    1,306
    #11

    Re: pedestal removal (wassupc)

    +1 on the craftsman adjustable strap wrench. You also might try some dry lube such as graphite rather than the wet stuff. Then once the seat is removed use an emory cloth to sand the metal base a litte where it goes in the hole if it is not the screw in type. I had someone recommend this to me a few years ago on this board and it worked. It was on the springfield seat base pole with the plastic tab that you have to push to release the seat pole.


  12. Member
    Join Date
    May 2007
    Location
    longmont
    Posts
    1,330
    #12

    Re: pedestal removal (Greenbacks)

    My friend has that problem. We put a pipe wrench with a 4 foot cheater on it and the result was a crushed post and its still stuck in there. We are thinking of hooking it to a hoist but im afraid to damage the deck.

  13. Member rkabusa's Avatar
    Join Date
    Jan 2009
    Location
    Fort Worth, TX
    Posts
    366
    #13

    Re: pedestal removal (crankn101)

    The key to using a hoist is just add little pressure and turn.just do it a little at a time. I got a little carried away and my seat tried to fly

Similar Threads

  1. pedestal help
    By shaneomac1 in forum Champion Boats
    Replies: 2
    Last Post: 01-31-2012, 06:06 AM
  2. Pedestal seat removal help?
    By Mindangler in forum Champion Boats
    Replies: 30
    Last Post: 01-08-2012, 10:32 AM
  3. Pedestal Seat Removal
    By RiverSnake in forum Cobra Boats
    Replies: 1
    Last Post: 04-12-2010, 04:20 PM
  4. Looking for pedestal- Need help!
    By Openfacereel in forum Champion Boats
    Replies: 18
    Last Post: 08-19-2008, 05:08 AM