Attn: guys with 06,07 ZX

[ChrisH]

Can somebody email me a pic if the passenger side cupholder. I need the one that is molded in the corner under the seat, not the flip down kind like I have. I'd like to see if Tiny's has one. Thanks!

[Neilslure]

Heres a pic from my 2008 ZX, should be the same as the 07.

[blackknife]

<table width="90%" cellspacing=0 cellpadding=0 align=center><tr><td>Quote, originally posted by Neilslure &raquo;</td></tr><tr><td class="quote">Heres a pic from my 2008 ZX, should be the same as the 07.

</td></tr></table>

show off!! just kiddin man!

Chris if you get one can you let me know how it works out, and maybe a part number & cost please? I think the glass under the seats in our boats juts out a bit, or maybe it indents in just the middle....I forget which or both

[ChrisH]

<table width="90%" cellspacing=0 cellpadding=0 align=center><tr><td>Quote, originally posted by Neilslure &raquo;</td></tr><tr><td class="quote">Heres a pic from my 2008 ZX, should be the same as the 07.

</td></tr></table>thanks Neil but the curve on mine is a little different. i think they started in 05, or 06...i found a pic on boats for sale here but it wasnt the greatest.

[512]

<table width="90%" cellspacing=0 cellpadding=0 align=center><tr><td>Quote, originally posted by ChrisH &raquo;</td></tr><tr><td class="quote">thanks Neil but the curve on mine is a little different. i think they started in 05, or 06...i found a pic on boats for sale here but it wasnt the greatest. </td></tr></table>

I can get a better pic than that because the pic you added from the for sale section is the same boat that I bought! Will try and find the camera

[512]

Here ya go

[blackknife]

ok....I want one! much better than the flimsy flip down plastic one!

[SkeeterJohn]

<table width="90%" cellspacing=0 cellpadding=0 align=center><tr><td>Quote, originally posted by blackknife &raquo;</td></tr><tr><td class="quote">ok....I want one! much better than the flimsy flip down plastic one!

</td></tr></table>

I was just thinking the same... althoguh i never use it and my partner probably hasn't noticed it before.

[ChrisH]

<table width="90%" cellspacing=0 cellpadding=0 align=center><tr><td>Quote, originally posted by 512 &raquo;</td></tr><tr><td class="quote">Here ya go


</td></tr></table>You are the man!! All you other guys: quit Copying me.

[ChrisH]

Have to get it from the dealer. Too new for Tiny's. Lee, IM sent.

[tnutz]

Do you know if that would work for an 02 zx? My 02 looks the same.

[ChrisH]

i dont see why it wouldnt.

[Dando]

Figure out the diameter you need and buy an aftermarket stainless steel cupholder. Nicer, prettier, sturdier, and...probably cheaper than a Skeeter dealer.

[ChrisH]

i need the whole assembly. not just the cup holder.

[Rick1067]

<table width="90%" cellspacing=0 cellpadding=0 align=center><tr><td>Quote, originally posted by ChrisH &raquo;</td></tr><tr><td class="quote">i need the whole assembly. not just the cup holder. </td></tr></table>

X2

How much are they?

[ChrisH]

$45 from my dealer. Gonna pay for it tomorrow. I'll post the part number when it gets here.

[Rick1067]

<table width="90%" cellspacing=0 cellpadding=0 align=center><tr><td>Quote, originally posted by ChrisH &raquo;</td></tr><tr><td class="quote">$45 from my dealer. Gonna pay for it tomorrow. I'll post the part number when it gets here. </td></tr></table>

Thanks

[650dozer]

are you putting it in your 03
I would like to the same to my 04 ZX 225

[Ranger391v]

The little differences over the years amaze me sometimes.

My '05 TZX 190 has this cup holer on the passenger side ...... thus I thought/figured all TZX/ZX 190's would.

They make good hook/sinker/bead/swivel holders ........ until they bounce around and fall down in that center hole.

[JL]

Did anyone get a part number on this? If so can you PM it to me, thanks!