Results 1 to 3 of 3
  1. 03-25-2012, 05:19 AM #1
    akstmstr
    akstmstr is offline
    Member
    Join Date
    Dec 2011
    Location
    Rochester
    Posts
    33

    Moved motor on jack plate, now it won't run.

    I had my 06 225 optimax out a couple weeks ago and it ran perfect. Then I took it to my marine and they checked the plugs, fuel filter, computer. Everything checked out fine. I then had them move the engine down on the jack plate an inch and a half. Took it to the lake. It started just fine, let it idle for a few minutes, went to take off and it flooded out, couldn't get it started again. So I trimmed it up and noticed fuel leaking out of the engine. Let it rest for an hour. Started it again and the same thing happened. I also noticed the bulb losses pressure after awhile. I also noticed if you trim the motor all the way up it compresses the bulb. I don't think I trimmed it all the way up prior to this problem but it is possible. Any ideas? THANKS
    Reply With Quote Reply With Quote
  2. low slung cruiser
    low slung cruiser is offline
    Member low slung cruiser's Avatar
    Join Date
    Jul 2008
    Location
    LKG, LITTLETON, NC
    Posts
    4,868
    #2 03-25-2012, 06:15 AM

    Re: Moved motor on jack plate, now it won't run. (akstmstr)

    your fuel line probally needs replacing...
    trimming it up, probally doesnt have anything to do with it...
    i have replaced 3 in the last 2 years....then i started running DONS cocktail, and KNOCK ON WOOD, haven't had to replace any more...
    Sterling 22XS / Mercury Pro XS V8
    Reply With Quote Reply With Quote
  3. EuropeanAM
    EuropeanAM is offline
    Mercury 3L/4 Stroke/Verado Moderator EuropeanAM's Avatar
    Join Date
    Apr 2008
    Location
    Greenville, SC (US)
    Posts
    98,378
    #3 03-25-2012, 07:56 AM

    Re: Moved motor on jack plate, now it won't run. (akstmstr)

    See the following post.... and ensure ALL recommended items have been addressed AT THE SAME TIME:

    http://www.bbcboards.net/zerot...first

    You <u>may</u> have additional problems.... but I would recommend addressing these items as a starting point.




    Dual Mercury Master Technician- for Mercury Outboards, Mercruiser and Mercury Racing at European Marine in Greenville, SC.
    Still consider myself a "Marine Apprentice" after 48 years (learn something new every day).
    Mercury Parts, Mercury Outboards, Smartcraft & Accessories, Injector Service, TDR Reeds- BBC Sponsor
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Lifting motor to install jack plate.
    By Phishinguy in forum Evinrude/Johnson Motors
    Replies: 3
    Last Post: 02-25-2012, 05:23 AM
  2. motor mounting on jack plate
    By chillywillie in forum Mercury Motors
    Replies: 8
    Last Post: 02-10-2012, 06:57 AM
  3. Lowrance Side Scan Transducer mount to Jack Plate skid plate
    By mbrund in forum Bullet Boats
    Replies: 10
    Last Post: 06-02-2011, 09:23 PM
  4. Motor to Jack plate bolts torque
    By Mark5795 in forum Mercury - 3 Liter & 3 Liter High Performance
    Replies: 14
    Last Post: 06-23-2009, 06:40 PM
  5. Home Made Jack Plate & Motor Trim Foot Control Plate
    By Nikon Man in forum Clever Tips & Ideas
    Replies: 11
    Last Post: 12-13-2007, 03:37 PM