Results 1 to 6 of 6
  1. 05-26-2021, 10:54 PM #1
    korferauma
    korferauma is offline
    Member
    Join Date
    May 2021
    Location
    Lily lake, IL
    Posts
    1

    lower unit assembly

    Hello all,

    I have a motorguide xi5 trolling motor and today it would run at full speed for about 30 seconds and then slow down and I was unable to get it to speed back up. I got home and opened the lower unit and found wires that were frayed so I put electrical tape around them and tried to close it back up. For some reason I can't seem to get it close back up now. I can't bring both ends close enough to get the long screws to connect to the threads.

    Is there a secret to getting the lower units to close back up?
    Reply With Quote Reply With Quote
  2. billnorman1
    billnorman1 is online now
    Member
    Join Date
    Apr 2012
    Location
    Insomnia, near Seaford Delaware
    Posts
    37,437
    #2 05-27-2021, 07:55 AM
    Metal doesn't compress. Frayed wires will not be fixed by taping them. You may need a new motor assembly, but someone here might be able to help you, not me. If there is an alignment notch on the housing that needs to be lined up if you had the magnet assembly off.
    Reply With Quote Reply With Quote
  3. Danrude
    Danrude is offline
    Member Danrude's Avatar
    Join Date
    Apr 2007
    Location
    Marietta, GA
    Posts
    3,574
    #3 05-27-2021, 08:48 AM
    Did you get the brushes back up on to the armature when trying to get it back together?
    Dan Burnette - Marietta, GA
    Triton 18TRX - 200 HO G2
    Reply With Quote Reply With Quote
  4. Bradrodfish
    Bradrodfish is offline
    Member
    Join Date
    May 2008
    Location
    Pierre Part, La
    Posts
    4,671
    #4 05-28-2021, 05:15 AM
    Agree with Bill and Dan is spot on. You did not open up the brushes to allow the brush end housing to seat with the center housing. Strongly recommend you change out the motor and shaft. You can not save the composite shaft when you try to pull it out of the damaged motor. It will mess the threads up and if you reuse it water will enter the motor again.
    Reply With Quote Reply With Quote
  5. JAZII
    JAZII is offline
    Member
    Join Date
    Jun 2004
    Location
    Scranton, PA
    Posts
    4,419
    #5 05-28-2021, 02:26 PM
    Quote Originally Posted by Bradrodfish View Post
    Agree with Bill and Dan is spot on. You did not open up the brushes to allow the brush end housing to seat with the center housing. Strongly recommend you change out the motor and shaft. You can not save the composite shaft when you try to pull it out of the damaged motor. It will mess the threads up and if you reuse it water will enter the motor again.
    The shaft has loctite on the threads. You can heat the metal motor housing where the shaft threads into it, which breaks the loctite for removal of shaft with no damage to threads.
    Reply With Quote Reply With Quote
  6. Bradrodfish
    Bradrodfish is offline
    Member
    Join Date
    May 2008
    Location
    Pierre Part, La
    Posts
    4,671
    #6 05-29-2021, 07:12 AM
    Quote Originally Posted by JAZII View Post
    The shaft has loctite on the threads. You can heat the metal motor housing where the shaft threads into it, which breaks the loctite for removal of shaft with no damage to threads.
    This troll motor does not have a metal shaft. It is composite
    If it were metal then you could do as you stated.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Tags for this Thread