Search:

Prior to installing mega live, I had helix 9 at bow and console, no network hub. They were networked directly via ethernet cable. To install mega live, I have to sacrifice the network connection from...

I have experienced this a few times. Unplugging and plugging back in the transducer cable usually does the trick. I assume you have tried this?

Wondering if anybody from NY has any recommendations for guided trips on st Simons island, in Georgia.

Species doesn't really matter. I fishing the finger, and great lakes for bass so I LOVE...

Hello,

I am from NY, and love to bass fish in the great lakes, as well as the finger lakes. Top water is by far my favorite way to catch them, followed by swim baits, and Texas rigs.

I am going...

Has anybody ever replaced the plastic housing on a PRO Charging Systems pro series charger?

I purchased a 4 bank charger off FB marketplace. When I received it in the mail, the plastic housing...

I did not measure any current between cranking battery negative, to the TM metal housing.

Thanks for the response Joe. I discovered that there is in fact a trim limit switch under the cowling. I was able to follow steps I found on the internet on how to calibrate it. Worked great and got...

Thanks CatFan. I can certainly measure this. Based on the current wiring I have described, I would expect this to show some current (cause of the electrolysis), and once I fix the wiring, I should...

Thanks Dean. I think this post confirmed what I am thinking. I have Batt 2 wire from switch, and ground strap going to the "high side" battery, and it needs to be on the "low side".

Anyway I can...

2015 ranger z119c w/ dual axle ranger trail trailer.

I am experiencing all sorts of trailer light funkiness that I am almost certain is being caused by grounding issues. When, and only when I...

2015 Ranger Z119C

I have been noticing a ton of electrolysis on my new to me 2015 ranger z119c. I see it all over, jack plate, zinc plates, trolling motor lower unit housing. And even most...

2015 Mercury 225 Optimax Pro XS - SN: 2B093135

I am having a few minor issues relating to my trim/tilt that I would like to address.

1. The motor will not trim all the way up, it get up just...

While doing some work inside the drivers console, I discovered the board that the timer module is mounted to had 3/4 of its bolts just about backed out. The board and the module has been bouncing...

This worked for me, kind of...

I attempted this on 3 different occasions.

First time, clicked the timer button only, great, turned on immediately and then cycled a few times. I did not time...

I think what you're referring to are valve positions, which I don't believe should have any influence on functionality of the timer.

I have read many forum posts, and review owners manual for my 2015 z119c, and am pretty confident with operations of the livewell pumps, valves, etc etc, but maybe I am missing something.

There...

2015 mercury pro xs 225 with 66 hours on it. Currently getting a non-critical fault code 41, indicating that the air compressor tempature sensor is not working properly. Any tips or tricks to keep in...

So is this plate that is welded to the port side, suppose to be the "seat" per say, for the jack?

1997 ranger r80 sport. Previous owner upgraded the jack, it is mounted on the starboard side of the trailer. I noticed on the port side of the trailer, in the same location, there is an additional...

The measurements of these parts seems to be correct, but i have a non-braked trailer.

I got all of this info from the rep as well. But he was not able to confirm if each hub, individually has to have at least 4200 capacity, or if the full axle capacity is split between two hub.

Called this morning to confirm bearing size after not finding what I needed. Could only finder tapered spindle assemblies. Can't get a pre-greased, ready to install assembly from then. Parts rep also...

1997 Ranger Trail single axle 3400 AWR trailer. I am looking for, preferably, pre-greased hub assemblies for straight axle with L68149 bearing both inner and outer. Can anybody help me out? Also, if...

this worked, now ive got to figure out why the trailer is not grounding.

They are standard bulbs. Yes, I have checked fuses, all seem okay. I would expect that if fuses were bad, then i would not be getting any voltage to the lights, which I am, just not full voltage....