Those old Delta Contractor saws were workhorses. The tube fence rails were maybe the weak spot, if there was one.
Type: Posts; User: bassboat1
Those old Delta Contractor saws were workhorses. The tube fence rails were maybe the weak spot, if there was one.
Mine comes off the top of the port side head. These are the only pics I have handy.
549172
Routing:
549171
I update with no issues yet. 3/93SV UHD + LS
One note on the Ridgid vacs - make sure it will accept bags (if your use will require them). I run a 20 yo Craftsman (made by Emerson Electric) with bags and a Cleanstream Filter for drywall dust...
I ran the 8-1/2" Makita job saw for decades in a Rousseau-clone table until a couple of years ago (pro remodeler). I replaced it with the 10" Skil Wormdrive. Tons of power, good dust collection, loud...
I use the Wlure hooks too. No issues with quality - just wish they made a greater variety of wire gauge and lengths.
Good going gents. Also all jerkbaits for me at Massasecum Sunday. 55 & and the small bass and bluegill have moved into shallow grass - couldn't find a batch of bigger ones, but the good bites were on...
Good going gents. Also all jerkbaits for me at Massasecum Sunday. 55 & and the small bass and bluegill have moved into shallow grass - couldn't find a batch of bigger ones, but the good bites were on...
Looks like it's on YouTube also
https://www.youtube.com/watch?v=bxGmNd9rwvQ
IDK the Ramp and Clamp - I've heard nothing but good things about it here. I fish solo at least 80 times/year at lakes with primitive launches/no docks, and the Drotto is probably my #1 accessory on...
I went from a rotating red Dewalt to a two-plane electronic green, then to a 3X360 Huepar 3X360. Green is visible farther than red. The Huepar fits my needs for all my interior requrements so far:...
The only one I've been through was locking up into Rodman/Lake Ocklawaha. Blew my mind that they'd move that much water for one Yankee in a plastic boat:smile:
Visited Okeechobee @Clewiston in...
I use a pair of 3/4" plywood/subfloor blocks about 7"x7", used a 4" holesaw on one and drilled some 1/2" drain holes in the other before screwing together. My driveway has a little bit of slope - I...
ball powder probably? I'd run them, just be alert for squibs.
I use a KastKing 7'-10" Mod/Med Speed Demon Pro with a Shimano Citica D (6.2:1 iirc). I throw 6XDs quite a bit, but nothing bigger. I get 10 more yards than the same setup with a 7'-4" glass Shimano...
Yes - our fish are usually bottom related and LS doesn't separate them as well as 2D.
Edit: re-read post title - OP was polling those "proficient with LiveScope", so I'll sit back down and shaddup...
The one that got me into bass fishing was the Bush Hog, back in the late 70's. It was all night fishing, baits were black on black and the boat was fueled by Bud Heavys.
Fished Highland Saturday afternoon. Got zero bites on a jig, spinnerbait, medium diver, jerkbaits or a blade bait (unless you count that one buck perch that jizzed on the entire front half of the...
One of my 93UHD was doing that recently - swapped it with one of the others and both are working fine. Suspect poor contact at the cradle. I didn't see any corrosion.
I use distilled water with a little white vinegar & microfiber.
Base material is surely stainless steel. Black nickel plated (translucent) or black oxide (all black).
I start with about 13'. Typical setup is 30# 8-strand braid FG knot to 8#-15# Seaguar Red or Daiwa J-Fluoro (lovin' the Daiwa stuff). I never notice the knot with moving baits. I'll get an...
I've had less than ideal results with AZEK's 1/2" trim the few times I've used it. IDK if I have installed the Trex fascia/bandboard yet (used it for risers). Most of my decks get cellular PVC band...
548183
Nice! This year's been lots of looking, to find a few scaly acorns! Success has been split between a jerkbait and a compact double-colorado spinnerbait for me. Haven't seen 50 yet. Crappie fishing...