Search:

Type: Posts; User: Kiss_my_bass

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    133

    14" Atlas Jackplate

    Is anyone here running a 14" Atlas on their boat?
  2. My skeeter has a primer bulb. Maybe try priming...

    My skeeter has a primer bulb. Maybe try priming it up before you start. It's probably just starving for fuel a little bit. you can also let the fuel pump run a second before turning the ignition...
  3. Replies
    3
    Views
    319

    I figured it out. The shift rod was in fact...

    I figured it out. The shift rod was in fact installed 180° out. I pulled it and rotated it and it slid right in.
  4. Replies
    3
    Views
    319

    I think the tech installed the shif shaft in the...

    I think the tech installed the shif shaft in the LU 180deg off. I went back with a clear mind and observed that when I turn the shift shaft clockwise the LU goes into Forward. When I move the Shifter...
  5. Replies
    3
    Views
    319

    HELP!!! Lower unit will not stab

    I just got my LU back from having the prop shaft straightened. The only way I can get it to stab is if the LU is in forward and the shifter is in neutral. I've tried the forward/forward,...
  6. Replies
    14
    Views
    729

    I know this is an old post, but what ended up...

    I know this is an old post, but what ended up being the solution? Mine is doing the same thing.
  7. I have a 2017 ZX250 and I have the opposite...

    I have a 2017 ZX250 and I have the opposite issue. The post will thread into the front but just spins in the back.
  8. Replies
    11
    Views
    628

    Can you renew extended warranties?

    Can you renew extended warranties?
  9. Replies
    3
    Views
    407

    2017 ZX250 and Gorilla Hull

    Has anyone else here had a gorilla hull put on their ZX250? I had one put on a couple years ago and I do not get the bow lift like I used to have and I've dropped from consistently running 72 mph to...
  10. Replies
    1
    Views
    342

    ZX250 Seats

    Does anyone have any 2017 ZX250 seats that they would like to sell or would know where I could get one. For some reason, the aluminum post that runs through the head rest broke at the top bolt hole...
  11. Replies
    3
    Views
    142

    I found one! Please delete

    I found one! Please delete
  12. Replies
    3
    Views
    142

    ttt

    ttt
  13. Replies
    3
    Views
    142

    WTB Gimble Bracket for HDS 9 Gen 3

    I found one. Please delete
  14. Replies
    7
    Views
    755

    looking at the pic, the first 3/4" on the left...

    looking at the pic, the first 3/4" on the left side of the blade is where it twisted off. There may have been an issue with the material in the center section of the blade the way the discoloration...
  15. Replies
    7
    Views
    755

    Just cruising at around 55 mph. Odd thing, there...

    Just cruising at around 55 mph. Odd thing, there was no impact and no discoloration to indicate that there was an existing crack before it broke.

    I ran the 27m prop over the weekend since I...
  16. Replies
    7
    Views
    755

    ZX250 w/ SHO and 27M prop

    Has anyone tried this combo? I threw a blade off my 25T2 prop on Tuesday and am in a time crunch. I have a mint condition 27M prop laying around and I was thinking about trying it temporarily until...
  17. Replies
    4
    Views
    529

    It was in the bag! Thanks!

    It was in the bag! Thanks!
  18. Replies
    4
    Views
    529

    2017 ZX250 Icebox Plug

    My boat didn't have a plug in the center seat cooler. Can anyone tell me what size plug I need to buy? The icebox doesn't hold ice long without a plug...

    Thanks!
  19. Replies
    10
    Views
    316

    Let me know how that goes. I'm having the exact...

    Let me know how that goes. I'm having the exact same issue.
  20. The hole shot with the 27-M was not affected vs...

    The hole shot with the 27-M was not affected vs the 25T1. This was using the 10" slidemaster. I have 4 batteries and a power pole as well. According to their current warranty, the 10" slidemaster...
  21. Was hoping someone could chime in! TTT

    Was hoping someone could chime in! TTT
  22. Z21 with Atlas 12" and Yamaha 27-M prop

    Is anyone out there running a Z21 with an Atlas 12" Hydraulic jack plate with a Yamaha 27-M prop on a 250 HPDI with VZ250tlr lower unit? If so how's it run? See any gains vs the 10" Slidemaster and...
  23. Replies
    32
    Views
    730

    Not really. They've all seamed to blend into...

    Not really. They've all seamed to blend into each other now. I guess Clear Lake is a conglomeration of Webster, Friendswood, Houston and League City. They are just one solid mass.
  24. Replies
    32
    Views
    730

    I grew up in the Clear Lake area and now live...

    I grew up in the Clear Lake area and now live near the Kingwood area. Personally I like the Kingwood area more. A lot less traffic and a lot more freshwater fishing options. (Lake Houston,...
  25. Replies
    3
    Views
    925

    Ranger Z21 Custom Dash

    Has anyone relocated the three main gauges on the dashboard in order to install an in dash chartplotter/graph. I'm thinking about removing the factory installed X135, replacing the metal plates and...
Results 1 to 25 of 37
Page 1 of 2 1 2