Backstrap
Type: Posts; User: Augustus
Backstrap
I had the same problem last year and it turned out to be a cracked reservoir. The crack was on the bottom and I only found it after removing it. Very small but just enough to have a fluid leak....
I installed the Ultrex pedal on my 2008 Z520 and it fit with no modifications to the trim ring or the tray. It's a tighter fit than the Fortrex and sits just a bit higher but operates just fine.
75 and feel every bit of it!
https://i.postimg.cc/FH5tqnF9/image.jpg
Mark, What did you decide to do on the timer?
I'm in the same situation only my charger is a 440. My boat sits for four months a year and for the past three years I have been using a seven day...
My 08 Z520 hull length is 20' 9'. Jack plate, motor, and trailer tongue add about 4'.
I have an 08 Z520 and use three lunchbox size soft side coolers for storage under my step. They fit perfectly. I use one to hold maps, spare sunglasses, lure retriever, and other paperwork. one to...
Make that, "four rear holes are two solid plugs and two LARGE opening plugs".
Sorry it took so long to reply. The Razor 4XL has 8 PVS holes. On my set up all the forward holes are open. Two of the four rear holes are solid plugs and two are medium opening plugs. My boat is...
I'm getting 67-70 mph depending on load and conditions at 5850 rpm. PTP is 2 3/4" most of the time. I've tried lowering it to 3" and 3 1/4" and it doesn't seem to make any difference in holeshot or...
I have the same set up, 2008 z520 with a 250HO Etech and a 24 Razor 4xl and concur with jc2bg on the 24xl. However, a 2009 250HO may still have the L2 lower unit. If you have the L2 you might call...
Rosie
I've got an 08 250 ETEC HO on a Z520 also. I had an injector fail in 2012 and haven't had any problems with injectors since then. I think it's a crap shoot whether one will fail or not. Like you I...
Had to be Schlitz in steel cans when I was in Viet Nam. You had to drink a few before the aftertaste went away. Close second was Singha from Thailand. I pretty sure formaldehyde was involved in...
36 V, 45” shaft: 81 lbs.
Well I figured it out but how do you just post the thumbnail?
http://www.bbcboards.net/attachment.php?attachmentid=314949&stc=1
http://www.bbcboards.net/blob:http://www.bbcboards.net/98c2023b-2d43-42a2-9463-1bd9d30e1f7d
I was fishing a creek channel last month that had a very shallow edge that had a lot of laydowns on it. I was kind of drifting down the channel with the wind and saw a bass about 15' away right on...
"Hell of a deal, ain't it, getting older"
On my Z520 I moved the batteries on the starboard side to the rear of the compartment and had enough room to mount both pumps in front of them. Much easier to install and also easy access for...
Thanks for the info. I would be happy with 69! That's interesting on the 25P Fury. The prop guru here in Texas, (Steve's Custom Props) recommends that prop for our set up. What was your holeshot...
I think we are running the same boat/motor/prop combination, Z520, Etec 250HO, Razor 4XL 24P. Mine is 2008. Recently I replaced the L2 lower unit with the M2 lower and I've really experienced a...
I was the Captain of a Southwest airlines flight that day. I had departed Tulsa on my way to Dallas and had just leveled off at FL 240 (24000 ft) when the air traffic controller came on the radio...