Search:

Thanks - I was thinking that was best approach unless I couldn't reach deep enough from the back deck. It turns out the back lid hinge is attached to the boat with just 6 screws on each side so...

I've got problems with my Flow Rite livewell valves. They are attached to the livewell pumps down in the bilge. What do people find is the best way to access this area - (1) from behind the transom...

Thanks Todd. I really appreciate the clarification.

I had assumed that all lakes listed as included in the g3 Ultra mapping on the Garmin website were supported with all the g3 Ultra features...

Many thanks Todd - much appreciated. One final question: I seem to remember when I first connected my Active Captain app to the unit it said something about me getting one free update to the g3...

Yes, I know the boat must be on the lake for it to work. After learning how the lake level adjustment works when fishing Lake Berryessa, I've tried it on several (3?) trips to Lake Sonoma and the...

Todd,

Under Supplemental Maps it shows (see attachments):
LVUS107A-Garmin LakeVu g3 Ultra US West v2022.5 v24.00

I appreciate your help!

You are correct - LakeVu g3 Ultra mapping. I'll grab the specific version off the boat and post shortly - i purchased the mapping card in fall of 2022.

Revisiting this old thread. I've got my networking bugs all solved and the Garmin units are working great. I have no trouble doing the lake level adjustment on Lake Berryessa (about 40 miles from...

Disregard - I ran over to the boat at lunch at measured them. Each livewell holds about 17 gallons when filled to the overflow drain.

I'm going to start using a livewell treatment to promote bass survival in tournaments. To decide how much treatment to add I need to know the volume of each livewell. Anyone have this for a 2004...

Thanks both - just what I was looking for.

Does anyone know how to find details on what changed in a Garmin software update? I always keep all my units (2 Echomap Ultra 126sv + Livescope Plus LVS-34) updated, but it would be nice to know...

Thanks Todd. I had the same question. Your solution worked on my AC (on iPhone).

The rubber toughened CA worked well. It was easy to apply and the edge trim is still in place after 3 weeks. I'd say give it a try - thanks for the suggestion.

Will do.

The rubber toughened CA looks promising. I just ordered some - will give it a try.
Thanks for the suggestion.

I'm sure it won't be nearly as expensive as new. Mark just repaired a badly damaged Tempest Plus for me and the cost was quite reasonable (and the workmanship quality was outstanding).

I have an '04 295 ProXL with a 200 Optimax turning a 25p Tempest Plus and I'm getting about the same performance as you.
I agree with the other recommendations. You're getting about what your...

Anyone have a good solution for keeping this trim on the free edge of the console fiberglass? It just slips over the fiberglass edge, but mine keeps falling off. I'm sure this is a common problem -...

After losing a blade were you able to use your outboard to idle back to the marina or was the vibration too bad even at low speed? I am just thinking how I would get home if it happened to me. ...

It looked a lot like a fatigue crack on the outside so that's very plausible, especially given the orientation of the crack. I think I'm running about 3.25" prop-to-pad so that's reasonably high but...

You were correct: Mark repaired the prop as good as new (at least in appearance), and it spent only a week at his shop.

I'm going to give it a test run. If it runs as good as it looks I'm going...

Thanks. I'll try out a couple of these things and see what happens. Seems strange to me.

On my console I have an Echomap Ultra 126sv connected to a GT8+GT36 via a Y-connector. I've had this setup about 9 months and it has worked great, so I don't think this is an installation issue.
...

Agree Jonny's an entrepreneur. As a serial entrepreneur myself I recognize the symptoms. It is definitely a good thing for him, as the YouTube gig likely has a finite run. I've heard Jonny give an...