Can you swap the bolt and pin and swing your tongue the other way?
Type: Posts; User: jb3601
Can you swap the bolt and pin and swing your tongue the other way?
2005 Mercury 200hp EFI 3.0. OT 973883. I noticed a lot of oil/gas residue coming from the front of my motor. it has coated my steering cylinder and running down the front of motor. I've looked...
I built my own from 2, 30lb hand control MK trolling motors. I made a bracket that goes between my Raptor and it's mount. Then bolted the TM to the bracket. Wired in a foot switch so I can control...
Get ya a Drotto Latch and problem solved. Like someone else sai, might try not backing in so deep.
Do you still have the mount for sale?
I have a new NOCO Gen pro 10x3 charger That's been on my boat about a month. I noticed it is going in Standby mode on my cranking battery. Anyone know why it does this? Battery is good and all hook...
I have a new NOCO Gen Pro 10x3 battery charger. I noticed it went in to standby or low voltage mode on my cranking battery. Checked volts with voltmeter and it's at 12.6. So I presume it's not low...
Thank you. I guess I never really paid that much attention to it in the 4 yrs I've owned it.
Mercury 200 OT973883. My trim gauge only works when the key is on. I'm pretty sure it was working with key in off position before we installed a set of Raptors and a new manual jack plate this past...
Got home today and pulled battery out. Pulled ign switch panel out. Didn't find anything wrong. Volt gauge and gas gauge started working after I re-installed battery and hooked all the wires back up....
They just hook right up to battery. No other wires to run or hook up. Gonna pull the panel that holds the ign switch in a bit and see if I can see anything wrong there. Crazy how it just started all...
This past weekend I installed a set of Raptors and a new Noco battery charger on my 2006 Triton Tr-196. Everything works as it should except for the volt, trim and fuel gauge. All the back lights on...
I already have the mounting brackets 1810362 and 1810363. My jackplate is the older CMC. I'll have to decide on whether to buy a new jackplate or the sandwich brackets. Thanks
I have the 1810362 and 1810363 brackets already. That other number you put up, 1810388 would probably be cheaper than buying a new jackplate. Thanks
I am looking for a 6" manual jack plate. Prefer a Z-lock or Slidemaster. NO CMC. Would like to find one no farther than 3 hours from central Arkansas. Bought a set of poles but the brackets won't fit...
Has anyone mounted a set of Raptors on a CMC manual jackplate? The bolts that came with the brackets are way too small and the bolts on the jackplate are much bigger. Any suggestions besides buying a...
Put the transducer on TM shaft and only use spotlock after catching a fish.
C & O Marine. They only had a couple left 2 weeks ago. Give Carol a call.
Finally found a replacement shroud for my boat. It's a 2006 Triton Tr-196. Anyone ever had the pleasure of changing one out? If so, was it a pretty simple task?
Try C&O Marine in White Bluff TN.
https://slab-crazy-outdoors.square.site/
Look up Slab Crazy Outdoors on facebook. They have replacement bushings and they are top notch.
Check out Slab Crazy Outdoors on Facebook. I know it's made by crappie fishermen but hey, it gets the graphs up where you can see them. Also can let it down when you're moving to another spot. Well...
I have a 2006 Tr-196. The driver side console shroud has broken in half on one side. I'm looking for a replacement for it. I've contacted C&O Marine and haven't heard back from them. Anywhere else...
Level tow vehicle and trailer. Measure from ground to top of hitch receiver tube (A). Measure from ground to bottom of trailer coupler(B). Subtract (B) from (A) and that's the drop you need. We sell...