Search:

Type: Posts; User: cooper.bohner

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    81
    Views
    5,944

    Not sure on the prop. Still the original one but...

    Not sure on the prop. Still the original one but will probably be swapping over to a 115 SHO because the reverse is gone on this current motor and upon start up it spits clouds of oil out of the...
  2. Replies
    81
    Views
    5,944

    Yup it lives at my family’s lake house up here...

    Yup it lives at my family’s lake house up here and occasionally makes some trips to vermont and the st Lawrence river. Dropped the jake plate 3” and then ran it and made a big difference. Got it all...
  3. Replies
    81
    Views
    5,944

    Launch day!!

    Got the garage door pulled off and packed every tool I own into my truck, Hitched the bass boat up and headed north to the Adirondack mountains. Left bright and early too since theirs ALOT of rules...
  4. I would say 5-10k based on prices near me. If it...

    I would say 5-10k based on prices near me. If it is in a good as shape as it sounds more towards the 10k mark
  5. Replies
    81
    Views
    5,944

    Finished wiring up the console which was quite...

    Finished wiring up the console which was quite the project. Defiantly was something I thought would go a little quicker but the 6 switchs and live well timer and all of that took a good chunk of...
  6. Replies
    81
    Views
    5,944

    Nearing a end...

    Well its not done yet, but some big strides have been made. But before the update wanted to share a tip that for rolling and tipping alexseal topcoat and probably most other top coats I found 3" foam...
  7. Replies
    81
    Views
    5,944

    Paint

    So, after a failed gelcoat attempt decided to go a different rout. I believe the main reasons for the gelcoat failing was due to inadequate temperature and it being applied to thin, because after a...
  8. Replies
    19
    Views
    687

    Had a 1988 stratos i got were you couldnt turn...

    Had a 1988 stratos i got were you couldnt turn the wheel at all without ALOT of force then snapped the cable and replaced it and now its good as new
  9. Replies
    6
    Views
    1,274

    So not the best pictures but this is what I did...

    So not the best pictures but this is what I did on the rod locker for the boat I'm re building. In the front PVC pipe rod tubes and on the back I used 3" Cable grommets off amazon, they hold rods...
  10. Check out tbnation.net I recall them having a...

    Check out tbnation.net I recall them having a graph mount that's made for small consoles
  11. Replies
    13
    Views
    681

    Use a hole saw and if the area you drill thru has...

    Use a hole saw and if the area you drill thru has a wood core make sure to seal up that wood after you drill it with either an epoxy for best results or even silicone around the edges. In my (little)...
  12. Replies
    81
    Views
    5,944

    I hate gelcoat...

    Well... I have ran into the dreaded gelcoat issues...

    So first off the boat was primed with an epoxy primer but very intense surface preparation was used and the issues are consistent over the...
  13. Replies
    21
    Views
    877

    I dont have ffs. But two unites on the bow one...

    I dont have ffs. But two unites on the bow one running side imaging and down imaging split. And the other full screen charts. I fish smallmouth mostly so having the full screen were i can see my...
  14. Replies
    81
    Views
    5,944

    Gelcoat and decking...

    Finally got the console and front of the boat gel coated. Still needs a couple more coats and with the temp being 50-60 need to wait for the first coat to dry since total boat only sells black with...
  15. Replies
    16
    Views
    1,296

    Also haven't got to use it on a bass boat yet but...

    Also haven't got to use it on a bass boat yet but in a saltwater application it is really great. The brand we have is Dekit and it has lasted a couple seasons without any pealing on a boat that's in...
  16. Replies
    16
    Views
    1,296

    Its expensive. To have it custom cut it was $36 a...

    Its expensive. To have it custom cut it was $36 a sq foot +600 to have it scanned and 200 for install that was on a 31ft boat though. Gonna take a shot of routing it myself on my current build to...
  17. Replies
    2
    Views
    273

    I had a similar issue with my hummin bird when I...

    I had a similar issue with my hummin bird when I got my boat. Think it was a loose connection on the power lead that caused it. Was reading 12v on the plug but once powered on got low voltage...
  18. Replies
    5
    Views
    408

    Not a talon but did it on my power pole. As long...

    Not a talon but did it on my power pole. As long as fuse size stays the same u won't have any issues.
  19. Replies
    81
    Views
    5,944

    Paint and primer

    Got almost the entire cap and decks primed. Need to go back and fair+re prime a bunch of spots along with sanding but its coming alone nice. Used total boat 2 part epoxy primer which does an amazing...
  20. Replies
    22
    Views
    2,713

    https://www.instagram.com/p/CplwXoPrIFe/?igshid=Ym...

    https://www.instagram.com/p/CplwXoPrIFe/?igshid=YmMyMTA2M2Y=

    saw this today so figured i would share. Might not be exactly what ur thinking of but could work
  21. Replies
    22
    Views
    2,000

    My 1988 16ft stratos fish and ski used to do...

    My 1988 16ft stratos fish and ski used to do pretty well in a breeze but it also had hundreds of pounds of water logged pour foam and plywood. Not sure if that would make a difference or not. But a...
  22. Replies
    3
    Views
    733

    I know minn kotas sight is out of stock so I...

    I know minn kotas sight is out of stock so I ordered from bass pro who had a bunch in stock and free 2 day shipping on the ultrex.
  23. Replies
    81
    Views
    5,944

    Pictures

    Been sanding away the past couple days, not quite ready for primer but getting close!
  24. Replies
    3
    Views
    324

    If its just stuck mabye a pitman arm puller?

    If its just stuck mabye a pitman arm puller?
  25. Replies
    19
    Views
    1,335

    Get two helix 8s with mega SI and DI. Fantastic...

    Get two helix 8s with mega SI and DI. Fantastic customer service and really good 2d imaging. You can also network them and add mega live, mega 360 and a ton of other stuff in the future if u want.
Results 1 to 25 of 85
Page 1 of 4 1 2 3 4