Search:

Type: Posts; User: 2014 nitro z7

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    284

    Llebroc seats.

    Llebroc seats.
  2. Replies
    3
    Views
    232

    I have a lot of ideas. But it seems as if your...

    I have a lot of ideas. But it seems as if your mind is blank.
  3. Yes, no or maybe

    Yes, no or maybe
  4. Replies
    14
    Views
    442

    You would think some one at Nitro would see these...

    You would think some one at Nitro would see these threads and realize their biggest complaints are the touch pads and trailers.
  5. Replies
    6
    Views
    321

    Try Great Lakes Skipper. They may have one.

    Try Great Lakes Skipper. They may have one.
  6. Replies
    1
    Views
    130

    On one end or the other the length will be on it....

    On one end or the other the length will be on it. Or at least it used to be.
  7. Replies
    2
    Views
    277

    Should have a coast guard plate that will tell...

    Should have a coast guard plate that will tell you max HP.
  8. Replies
    8
    Views
    543

    I agree with the above statement. It will be...

    I agree with the above statement. It will be cheaper to take it to a mechanic than replacing a power head or new engine. Just my opinion.
  9. Yes it is a legitimate problem, my post was...

    Yes it is a legitimate problem, my post was direct to Shotgunz.
  10. OK,we get it you hate Nitro boats.

    OK,we get it you hate Nitro boats.
  11. Replies
    44
    Views
    4,358

    There is NO way that happened at the factory and...

    There is NO way that happened at the factory and after several years you finally notice it. Just looking at the pictures that sticks out like a sore thumb.
  12. Make sure the terminals are clean and the nuts...

    Make sure the terminals are clean and the nuts are tight.
  13. Replies
    7
    Views
    411

    I have a carabiner on mine, just because it's...

    I have a carabiner on mine, just because it's easier to snap on.
  14. Mine has 2 plates that go on when the console is...

    Mine has 2 plates that go on when the console is removed.
  15. Replies
    18
    Views
    1,046

    I'm not sure what is meant by the last comment....

    I'm not sure what is meant by the last comment. But, chevy you have a beautiful boat.
  16. Replies
    13
    Views
    1,081

    Main concern is if I have to drill new holes is...

    Main concern is if I have to drill new holes is to protect the gas tank.

    Might check how deep you need to drill then wrap drill bit with tape. That will stop the bit from going to deep.
  17. Replies
    28
    Views
    2,332

    Without a doubt I would purchase another Nitro.

    Without a doubt I would purchase another Nitro.
  18. Replies
    5
    Views
    380

    Slow process, but remove fuel connector from...

    Slow process, but remove fuel connector from motor and use it to siphon gas.
  19. Replies
    18
    Views
    834

    I believe you can go through Mercury and extend...

    I believe you can go through Mercury and extend the motor warranty. Sorry this doesn't help with boat,but it may be something to check on.
  20. Replies
    20
    Views
    3,175

    jtrac,could I get the info on the box also....

    jtrac,could I get the info on the box also. Thanks in advance.
  21. Replies
    5
    Views
    582

    Use a hole saw and cut hole as low as you can...

    Use a hole saw and cut hole as low as you can under the control box. The put a stainless clam shell over it. Hole is hidden and cable is run. Just my thoughts.
  22. Replies
    8
    Views
    2,602

    Cost of getting will not be near as steep as...

    Cost of getting will not be near as steep as getting rid of. LOL
  23. Replies
    14
    Views
    5,430

    That's going to cost you more than a thousand.LOL

    That's going to cost you more than a thousand.LOL
  24. Replies
    3
    Views
    442

    Silicone spray works great for this. My son in...

    Silicone spray works great for this. My son in law worked at a mattress factory during his college days and told me they used it to remove glue residue. Finally found something useful that boy got...
  25. Thread: Old Man

    by 2014 nitro z7
    Replies
    5
    Views
    1,833

    Do not mess with old people!

    Do not mess with old people!
Results 1 to 25 of 145
Page 1 of 6 1 2 3 4