Search:

Type: Posts; User: Bradrodfish

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Go to the hardware store and find a solid rod the...

    Go to the hardware store and find a solid rod the size of the holes. Not sure the size, but if you have some bolts around the house you can use them the size the hole. Bend the rod the shape of the...
  2. Replies
    5
    Views
    411

    :beers: Thanks to all

    :beers: Thanks to all
  3. Replies
    3
    Views
    108

    [QUOTE=mampro;13433598]Hello, I have a 2018...

    [QUOTE=mampro;13433598]Hello,

    I have a 2018 Ranger 2510 bay boat with an Atlas jackplate and a Yamaha 300. I just purchased two minn kota raptors and would like to mount them onto the jackplate....
  4. Replies
    5
    Views
    114

    Lowrider is is spot on. With no water in motor it...

    Lowrider is is spot on. With no water in motor it is pointing at the armature. Make sure you replace the seals too.
  5. Replies
    5
    Views
    114

    You probably have water intrusion in the motor....

    You probably have water intrusion in the motor. Store it remove prop loosen 5/16 thru bolt and see of water drips out.
  6. Replies
    5
    Views
    202

    That is rare is correct. I have not seen this...

    That is rare is correct. I have not seen this happen to anyone local. Yes all they have holding it is the spline on the pin.
  7. I can only say that I have no experience with any...

    I can only say that I have no experience with any of them because I never owned any. I work mostly on Minn Kota. I have changed a hand full since the GPS came out. A few would not lock on the...
  8. Replies
    5
    Views
    411

    :thumb up2:

    :thumb up2:
  9. Replies
    5
    Views
    411

    Clearing things Up

    First I want to say that I was wrong on a statement, for which I could not find, about Quest and Non Quest troll motor related to GPS Systems. Slydoogie was totally correct in his statement and i was...
  10. Replies
    7
    Views
    161

    I operate a Motor Guide repair shop. I have...

    I operate a Motor Guide repair shop. I have access to drawings and I knew about this mount becase I had several in the shop a few years ago. Got rid of them in metal trash because they were in the...
  11. Replies
    7
    Views
    161

    Hr correct part number is MCK36101. There is one...

    Hr correct part number is MCK36101. There is one on eBay.
    ...
  12. There were no recalls on this motor. There were a...

    There were no recalls on this motor. There were a number of service bulletins on this motor. By the time this unit was built all the issues were taken care of.

    Unless you know this guy I would be...
  13. Replies
    7
    Views
    161

    If you can post a picture of the part you are...

    If you can post a picture of the part you are looking for. Maybe I have one in the shop. I am not sure what you need based on your description. The Parts are very hard to find. You might get lucky on...
  14. Thread: Quest ?

    by Bradrodfish
    Replies
    5
    Views
    295

    It should not be very hard to operate. The only...

    It should not be very hard to operate. The only adjustment is to take the push button off and then raise the reed switch up a fraction. You have to be careful with this adjustment because if it is...
  15. Ok. Looks Like you know something about power. ...

    Ok. Looks Like you know something about power. It is best to check the steering system with the remote. It will be much easier. You did say it does not steer in either direction with the foot pedal...
  16. :thumb up2:

    :thumb up2:
  17. Replies
    1
    Views
    100

    Remove the cover. Line it up with the lower....

    Remove the cover. Line it up with the lower. Reinstall the cover.
  18. You have either a bad steering module or a bad...

    You have either a bad steering module or a bad control board or both. It is best to bring to an ASC.
  19. The only thing I would be concern about is the...

    The only thing I would be concern about is the corrosion of the inside of the part where the prop shaft seals sit. With time it could cause water to enter the motor assembly. Uless you want to change...
  20. Replies
    6
    Views
    147

    HUMM. Electric Engernear. This job may be far...

    HUMM. Electric Engernear. This job may be far above your means.:laugh::nanner:
  21. Did you buy it new or used? What I am seeing...

    Did you buy it new or used?
    What I am seeing here is a classic sign of oxidation(corrosion) on aluminum. I see it a lot here in South Louisiana. It is hard to stop it. That is pretty bad. It will...
  22. Replies
    6
    Views
    147

    Well I would say that if you did not find a Utube...

    Well I would say that if you did not find a Utube video it is because it is not easy. You have to remove the foot pedal cables and the head of the troll motor to replace. My advise is to bring it to...
  23. Replies
    6
    Views
    162

    Have you checked your batteries? They all should...

    Have you checked your batteries? They all should be load tested to find a bad one. Also check all connections for corrosion and tightness. 38 volt just means that you can read a voltage, but when you...
  24. Replies
    3
    Views
    106

    The Raptors come with two remotes along with the...

    The Raptors come with two remotes along with the hardware to mount them at the console or use with a lanyard.
  25. Replies
    8
    Views
    331

    You either have the pivot bushings out or you...

    You either have the pivot bushings out or you have a twist in the mount. Look at the upper arm and see if there are any rub marks on one side or the other. Remove the side plates and to the rear of...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4