Search:

Type: Posts; User: Michael Stelly

Page 1 of 9 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    114

    Hot foot 2014 Pro XS

    I installed a hot foot in my boat, I want to make sure the cable is adjusted properly. should that butterfly touch the stop when WOT. If so I can’t see to get it to open that far.

    524853
  2. Replies
    2
    Views
    107

    2014 Optimax Pro XS150

    New owner of a 98 triton TR18 with a 2014 Pro XS 150, 2B113749. I replaced the spark plugs and noticed all 6 I removed were not gapped correctly. They were all set .030-.032”, was that the original...
  3. Replies
    8
    Views
    308

    Thanks. I guess the TR18 does not have...

    Thanks. I guess the TR18 does not have recirculating pumps. I replaced both fill pumps and one of the pump out pumps.
  4. Replies
    8
    Views
    308

    thanks, I have replaced all the terminals on the...

    thanks, I have replaced all the terminals on the switches. My current problem is that some of the wires were so corroded and they fell off from where they were attached and I am not sure where they...
  5. Replies
    8
    Views
    308

    Hi, I agree with the wires corroded, several of...

    Hi, I agree with the wires corroded, several of mine were bad, cut some of the wire off and put new terminals. I only see two aerators, two live well pumps and one Bilge pump. Should I have...
  6. Replies
    8
    Views
    308

    Thanks, I found one from 2004 model. On my panel...

    Thanks, I found one from 2004 model. On my panel they have two aerator switches, one ACC, was this common? and do I need both. Only have rear port/starboard live well with drain pumps. All but one...
  7. Replies
    830
    Views
    462,715

    Sticky: New to me, 98 TR18 with 2014 Mercury Pro XS 150 ...

    New to me, 98 TR18 with 2014 Mercury Pro XS 150

    523492523493523494
  8. Replies
    8
    Views
    308

    98 TR18 (Electrical help)

    Hello, new owner of a 98 Triton TR18 with a 2014 Mercury Pro XS150. I am looking for a picture of the wiring of the main switch panel, color code or wiring diagram. I am replacing corroded...
  9. Replies
    6
    Views
    357

    Double post

    Double post
  10. Replies
    6
    Views
    357

    Shop called today said it’s the power pack that’s...

    Shop called today said it’s the power pack that’s causing intermittent loss of fire. Ordered power pack, hope this solves the problem.
  11. Replies
    3
    Views
    274

    Thanks. Local shop said key won’t work? I...

    Thanks. Local shop said key won’t work? I mean it’s a momentary switch. Guess I could try.
  12. Replies
    3
    Views
    274

    Johnson - Mercury swap

    I am having trouble with my 97 Johnson Fast Strike 150. I would like to remove the Johnson and install my xri 150. I know the control cables are not the same, how do I remove the OMC control box. ...
  13. Replies
    6
    Views
    357

    Twice it has left me in the water. Not sure I can...

    Twice it has left me in the water. Not sure I can trust it. Compression average 110lbs
  14. Replies
    19
    Views
    1,393

    Same type of problem I am having. I am...

    Same type of problem I am having. I am following this
  15. Replies
    6
    Views
    357

    97 Fast Strike 150 problem, J150GLEUE

    Went out on lake on Friday, motor cranked easy. Slow speed from launch then got on step. Almost immediately the motor sputtered slightly and died. Would not start. Used troll motor to get out of...
  16. Replies
    11
    Views
    1,520

    Ok. I will call them in a few minutes. Thanks

    Ok. I will call them in a few minutes. Thanks
  17. Replies
    11
    Views
    1,520

    I took boat to local shop. They pressure checked...

    I took boat to local shop. They pressure checked lower unit and determined it’s the seal under water pump that’s bad. They offered two quotes, one for just that seal and another from prop seals...
  18. Replies
    11
    Views
    1,520

    Thanks for help.

    Thanks for help.
  19. Replies
    11
    Views
    1,520

    thanks. I was quoted three to four hours of labor...

    thanks. I was quoted three to four hours of labor to repair plus parts of lower unit. Do I need special tools to replace seals. The lower unit is easy to remove
  20. Replies
    11
    Views
    1,520

    96 Johnson 150 Fast strike

    I changed water pump and found water in lower unit oil, milky oil. I took boat to local shop a week ago but they have not got to it yet. I loooked around for a working lower unit, found a GT150...
  21. Replies
    4
    Views
    408

    Thanks for information. My lower unit has water...

    Thanks for information. My lower unit has water in oil so the other stuff will have to wait.
  22. Replies
    4
    Views
    408

    I will check the weekend. The prop is 23p

    I will check the weekend. The prop is 23p
  23. Replies
    4
    Views
    408

    282 FS, 97, Johnson 150

    Today I picked up a super clean 282 FS with a fast strike 150. Test rode the boat and it ran very well. The speed of the boat is way lacking compared to my previous Astro boat. I guess it would be...
  24. Thread: 200SX

    by Michael Stelly
    Replies
    0
    Views
    1,892

    200SX

    Any 200SX owners, I have the opportunity to purchase a 200Sx without a motor. The Mercury 150 was removed and sold. The gel coat would need wet sand and compound. Seats are not perfect but usable. ...
  25. Replies
    2
    Views
    104

    Awesome. Thanks for information

    Awesome. Thanks for information
Results 1 to 25 of 224
Page 1 of 9 1 2 3 4