No doubt about it money can be saved, especially on the higher end setups I feel like. I’ve been doing a bunch of reading over there and on tackletours rod building forum as well as YouTube videos....
Type: Posts; User: YamahaRacing55
No doubt about it money can be saved, especially on the higher end setups I feel like. I’ve been doing a bunch of reading over there and on tackletours rod building forum as well as YouTube videos....
Looking for recommendations on a rod building kit. Mudhole and getbit are the two I’m looking at but not sure if one’s better than the other or more user friendly etc. or if there’s a better route to...
I seen they had the 10 for 600 sale going on and was debating it. Just thought it might be overkill for someone who’s never even built one yet. I may still do it though..
Rookie question here but...
Spoon that comment was in reference to willwork4fish just fyi.
what’s your opinion on the xfast vs fast for fishing close quarter cover with tx rigs and jigs?
Pretty expensive blanks to build on just to disappoint on that aspect..I was hoping to hear good things about them. I’m interested in starting to build rods for me and my dad and trying to gather...
Good info spoon, do you have any experience with any of the blanks you mentioned?
JasonG did you ever end up moving forward with the pb73mhxf? I’m considering building one as well and curious about this blank
Great information alx I’ll definitely check those models out, i spoke with you before buying the hustler and it’s been everything i was hoping for and have since bought my dad and a good friend one...
Looking for somewhat of a specific crank rod. It will be for 1.5/2.5, 6th sense mvmnt squarebill duty in shallow “heavy” cover (laydowns, piers, brushtops etc) Leaning towards a composite/graphite...
Are these no longer being sold/produced?
+1 for the ALX hustler. Excellent shallow-mid crankin stick and has worked for 5XDs fairly well alao
Just had a similar issue. It was “due to low voltage” engine went to crank and had a “kickback” from battery voltage dropping to low, broke the starter bracket and damaged the starter. Engine was...
Looking for Kistler ZBONE 7’+ H
346-774-3422 send pics for quicker response
Looking for a helix 12” G3N or G4N + to run mega 360 with. 346-774-3422 Blake.
Thanks guys, when you say flush clean what the best method to do so?
Thanks guys, just realized I have one fat boy I picked up at a Walmart six or seven years ago still ha.
No tape on spool, and wasn’t doing it untill yesterday. Thinking it’s bearings. Would it be just the one on inside of side plate and the other on handle side??
21 Zillion is a sweet reel. Ordered mine from the tackle trap.
Out fishing yesterday and seems like my tatula sv 20 model (6.3:1) is making some noise on harder cast, I don’t notice when pitching or roll casting close quarters but seems like when spool gets spun...
Looking for a cara or expert spinnerbait rod. Let me know what you have, also have a mint condition alx zolo rumble could trade if interested.
Replacing hooks and tuning are more or less expected for me, or should I say I don’t mind doing either, and prefer to replace hooks with a short shank and go up one size when I can. I did order a...
Lakes been super muddied up recently and my crank bite has slowed a little, thinking of upsizing to help the fish locate the bait better.. I’ve used the kvd2.5 in the past but wondering if there’s...
Just ordered a 1000yd soool of tatsu 17#. It shows to be the same diameter as the invizx 15#, so hopefully the strength is still there .
Ive been using 15# invizx on my shaky/wacky worm setup and...
4738022nd day throwing the alx hustler landed me my new pb on a crankbait. I was happy with how the rod had been performing before landing this, and even happier with it after seeing how it handled a...
I Just gave a small review of the hustler, which is their 7’0” MH glass crank rod in a few post down from this. It is Lightweight, plenty sensitive to detect bottom composition and/or when your...