548553
Type: Posts; User: thedude
548553
548552
Old pics with 10 and 9" replaced 9s with 12s since.
For the front graphs I used a 3/4 thick piece of plastic cutting board from Amazon and used my existing deck mount to stack a 10 and 12" garmin.
The dek-it console mount fits perfectly between the gauges of a 199 dash. I have it on my 13 with a 10" garmin which is the same cradle as the 12"
https://prociseoutdoors.com/dek-dash-mount/
If your switch doesn't do that, then its broken which is pretty common. There is a kit from flow-rite to rebuild it. It shouldn't drain in auto or recirc. If you have a plug in your livewell drain...
its not that complicated, there's 3 positions on the valve. When its on auto, the pump pulls fresh water from the lake, when its on recirc it pulls water from the livewell. In both cases, water is...
there is manual fill and then the fill that is on the auto/empty/recirc switch.
you likely plugged the intake one so your "auto" is not pulling fresh water, just recriculating whats in the...
get the Dek-it console mount. it was a perfect fit to bolt between my gauges and i've run a 10" garmin, 10" solix and 10" hds 2 on it. you could put a 12 there but it would really obscure the gauges...
i saw this place on facebook posted recently they had sourced a replacement brain box, they may also have keypads
https://www.facebook.com/wetumpkamarineelectronics
(no affiliation or experience...
the drain is both an inlet and outlet. There is a valve made by flow-rite on that line. In "empty" the baffle allows water out. In auto, it allows the pump to pull fresh water in, but does not allow...
fish move around a ton in the bays as they are bait oriented and nearly pelagic. the small ones stay shallow as "residents". That is not to say you won't run into good fish up shallow on a feed,...
well i just looked and i guess the price has gone up just like everything else#43039R / #43039L are the assembler with calipers ~ 420$
#43038U - (rear) idler hub - ~$220
I took a stab at...
depending on the age of your vault hubs - i would say just buy new ones. They sell the idler and caliper hubs fully assembled on a new torision arm. Last i looked the caliper ones were around 300$...
the entire chain is pretty good that time of year, but gets a lot of pressure (end of year tournaments, out of state clubs). That said, torch is a different animal. plan on covering a LOT of water....
the entire chain is pretty good that time of year, but gets a lot of pressure (end of year tournaments, out of state clubs). That said, torch is a different animal. plan on covering a LOT of water....
to my knowledge, Great Lakes topography is all provided by NOAA or USGS and is pretty good all round (its the great lakes so well documented for commercial navigation). All the map providers get...
i havent fished there for years but it was always a good (semi-private) lake. They should be on beds if not almost done. Lots of shallow weed edges. Traps used to be good in the spring and summer. ...
if you don't have a hole in the dash (like a flush mount graph hole). then you just add fluid into the tube. get the sea-star adapter that fits over the bottle and screws into the fitting at the end...
i have a 10" atlas on my 199. You shouldn't have to remove the tank. Its tight running wires through the top of the transom cap but you should be able to route them with existing transducer wires or...
can be good in spring but not the easiest place to dial in on them quick. nice lake to stay on though. The bay is pretty close as are a few smaller lakes that will be easier to find fish on.
D&R sports KZO, Great Lakes Communications in NE side of GR
this has been my experience as well - anything over 60 - even like a 6" boat wake remnant on flat calm would grab the bow - not something my 2s ever had an issue with, even at 70.
that said i've...
can you elaborate on what you mean by the steering jam nut?
also how did you adjust the throttle (like hot foot stopper or something under the cowl)
there's no fuses. you may have a breaker in the bilge area that tripped - mine was on the driver side outside wall of the bilge area kind of behind my starting battery. There was a 2nd breaker on the...
one of the best boats made. The only issue i think with the 211 was there was 1 year where they had a hook in the hull around the transom.... i think it was only a handful of rigs and may have been...