The spot lock disengages before it rotates all the way to sterm.maybe 3/4 of the way. The pedal has quite a bit of travel left before it bottoms out. I think cutting the trim ring might be enough...
Type: Posts; User: wi_yooper
The spot lock disengages before it rotates all the way to sterm.maybe 3/4 of the way. The pedal has quite a bit of travel left before it bottoms out. I think cutting the trim ring might be enough...
I already pulled the carpet on the left side of the recessed tray to bias the foot pedal as far to that side as possible. I might have to pull the right side carpet as well and cut a notch in the...
Is there a way to decrease the sensitivity for spot lock to disable when the pedal is touched? My recessed tray is really tight and the speed control knob barely rubs but it disables spot lock when...
Pm sent
Thanks guys. Right now where I have it mocked up it would be almost identical to having it on the hole shot plate.
Pm sent
Will do.
It was suggested on the humminbird forum that I ask here as well. Hight speed is with a thru hull so no need for the transducer to be in the water while on plane.
I am mounting an SI transducer...
Steve,
Thanks for the response.
No high speed operation for the SI transducer. I have a high speed transducer glassed in. The picture you posted shows the transducer above the boat hull, so I...
I am mounting an SI transducer on a 2006 Ranger 519 using a TS jackplate mount onto a Bob's 6" plate. I cannot seem to find any specifics on the mounting height for the transducer relative to the...
I have a '06 519 and I replaced mine with an F2. I had to route the winch strap off the bottom of the drum and then you can winch "backward" or swap the handle to the other side - either way works. ...
What pith are you looking for? I have a 26P old style raker sitting on the shelf if interested.
Ok - I just went and looked - my winch tower is different. My winch sits flat, not angled as yours does. The winch bolts furthest from the bow stop are 6 3/4". That leaves about 1/2" between the...
That looks like the same winch stand I have on my '06 519. My winch seemed to sit further back so you may need to drill new holes. That said, mine fit fine in my factory holes, but I did have to...
'06 519 w/ 200 HO E-Tec, 6" Bob plate
26P Raker II
71mph and change best speed, with 68 - 70 Fully loaded
I run my motor quite a bit higher. 2.75" - 2.5" PTP. If I am down lower I do lose...
My '06 519 w/ 200 HO and the 26P Raker II will run over 70 GPS at a tad over 5700 RPMs. I am between 2-2.25" under pad. Lower and I lose significant speed
Thanks Much
Guys,
Anyone have the mixing ratio for Ranger gelcoat to hardener as well as the specifc hardener (MEKP?)
I lost the instructions from Ranger...
Thanks!
I have an '06 with an E-Tec HO. My boat wants the prop to pad a lot higher than what others say. I run about 2" under pad. With two guys a full tanks I can get about 68MPH Best I have seen is 71...
On my '06, the gas gauge needle is sticking now - the last year or so. I 'think" it is due to the fact that the small gauges from that era allow water in. After a rain I can actually see water in...
I ran a 22 Raker (old style) on my 375 with a 150 Evinrude XP on it. Speed was right around 60mph.
I have the same year 519 w/ 200HO and a 6" plate. FYI Ranger only warranties a 6" plate in that year. I can spin a 26 Raker II to a bit over 5700 RPM and get 70+. However, I run my motor quite a...
I had one with a Rude 150 XP and ran a 22 raker
Some models had a hole for the net handles. Not sure about that model, but maybe.....
Thanks for the input guys - much appreciated!