Still looking.
Type: Posts; User: Kbahus
Still looking.
I am looking for the 24 pin gold connector with male pins in the back of the unit. Can’t get a pic to upload.
In the ongoing saga of trying to repair a broken pin on the back my electronics guy is willing to swap the connector if I can find another. Does anyone have a 93SV Echomap Plus head unit that has a...
Well some good news, I dropped by the local electronics guy and he was pretty interested in trying to fix it so I left it with him. I will keep you guys updated with what I find.
To replace a pinion seal you have to remove the pinion flange, to do that you have to remove a big nut, that big nut preloads the pinion gear. Typically there is a one time use crush sleeve that has...
I sent an email to Clear Cast Marine as they seem to be a popular repair center. Good idea on the electronics shop, I have a reputable computer repair guy that might be able to do something with it,...
Well that is not good to hear.
I have a Garmin 93SV with a broken pin on the back. I called my nearest Garmin service center and they informed me that they no longer do repairs on the pins and the unit is a "throw away". Has...
Looks like it was the remote, I am guessing the loose terminals on the circuit board was the culprit allowing intermittent contact. I have been out probably 5 or 6 times now with no issues. Thanks...
Great suggestions so far and if the remote has been communicating intermittently while trying the foot pedal that would explain some things. I haven't had time to get back on the water, but I did...
I will swap some fresh batteries in and try to isolate if it is either just the foot pedal or the remote, should be out on Friday to test it.
My Xi5 is great when it works, but lately it has been really testing my patience. I have had an issue where I deploy it, all the lights come on and GPS connects, but the remote or the pedal will do...
I have a 99 TR18 and went through a lot of my wiring a few years back. When you strip the insulation back you are going to find corrosion that has traveled up the wire core so be ready for that. My...
These were blisters prior to taking this picture, it can happen so keep an eye on it.
https://forum.ih8mud.com/media/8c80e420-1c11-4331-bd56-58f963ba425b-jpeg.99279/full
The cost is going to vary quite a bit depending on who can find to do it, I would plan on several thousand.
Yes it can only get worse. The blisters can open up exposing the fiberglass core allowing water to saturate the fiberglass ultimately leading to delamination. The blisters are caused by water...
Text sent regarding the SLX.
Looking for a set of brackets for a Uflex PTS-1 paddle trim unit. I purchased a used PTS-1 and come to find out they have two different size brackets depending on if your helm is a tilt helm or not....
Interested to see the pics when it is done.
Make sure to check the plastic housing that the brake pins are seated in. They can crack and it will cause a clicking noise when casting.
Great info, thanks guys. Maybe I will sell this one, but I will try throwing some jigs with it first and see how it does.
Last year I picked up my first GLoomis rod on an impulse buy due to a good deal. The model is "spin jig" GCX783S, 6,6" MH Fast paired it with a NASCI 2500 and 10lb braid. I am having a hard time...
Looking to trade or sell a Shimano Ci4+ 2500 for parts. No bail assembly included as shown in pictures, I was hoping to fix this reel but parts are prohibitively expensive. Would be willing to...
I would say the 150 EFI Merc 2-stroke on my 99 TR-18 is barely adequate to get the boat on plane loaded up with full livewells, even with a 23P Tempest. It would be a waste to spend the coin and be...
I am pretty convinced I am going to switch from 2x6 to 2x4 boards and likely go with Gatorbak covers. I checked out my friend’s TR19 today and it was sitting on 2x4 bunks. I think the smaller board...