The purpose of Stableview is for use in rough water when the transducer is bouncing up and down; the purpose is to smooth out the image. I only turn it on in rough water.
Type: Posts; User: Marc Marcantonio
The purpose of Stableview is for use in rough water when the transducer is bouncing up and down; the purpose is to smooth out the image. I only turn it on in rough water.
So on the back of your bow LIVE displaying the Scout mode, you have an ethernet cable between your AT2 box, and your bow LIVE showing Scout mode. Do you have a second ethernet cable on the back of...
Being military myself I get not going into battle without knowing all your weapons are functioning perfectly. When you get a chance make sure your NMEA 2000 network is functioning properly. Check...
Did you install it with the app, or by microSD card? Sounds like you need to reinstall the update.
You might have something wrong in your ethernet cabling that is preventing the data from sharing with your console unit. Can you directly connect an ethernet cable between the 2 and see if it then...
https://youtu.be/pvWpSb23IMs?si=kebdRaL9MKHAJ2ES
Thank you for the information. I will download the update tomorrow, but likely won't be able to test it out for a couple of weeks due to tournaments.
I run a TM150M with the latest software and have no issues that I have seen. I do use a custom frequency and not medium chirp, so cannot speak to that.
I use a 5A fuse.
Never knew the Ghost motor had an accellerator; frankly this video makes no sense. He says you can change directions by simply pressing the accellerator and you will keep going, but he also says you...
Thanks for the update...never had a terminating resistor go out but now I will know it is a possible source of a NMEA network problem.
Agreed, SS3D if my preference also. I will get the 3in1 HD nosecone for my Ghost to complement my SS3D and have the best of both worlds where I need them.
I show how to do this in my video of installing Dual AT2 units (part 1 and 2). The part about getting into the starboard rod locker is in part 2:
Dual Active Target 2 Install and Transducer...
That is a "trick" question in that there is an offset correction that can be applied in the menu, however, this is treating a symptom and not the problem. While it may help you in one direction it...
Yes, Blue Seas are the best, and you can get one for a single connection, or multiple connections. Get one that takes blade fuses and is water resistant. I attached mine to my hull under my bow...
Because of the difference in wire size, and for other reasons, I recommend you terminate the 10gauge wire to a fuse block, then install a 5 amp fuse in the block at the position where you connect...
Not likely assuming you just disconnected it and reconnected it.
I don't usually post fishing videos on this board but wanted to share this one from yesterday's trip to nearby American Lake in western Washington. Please help to support my channel by liking and...
The Point-1 normally comes with a 15-foot cable and one tee.
You should get a NMEA2000 starter kit which comes with a power node with Tee, and two 2-foot drop cables with Tees, a 15-foot cable...
This ^^^^. Try stopping your SideScan and DownScan and see if the lines go away. If this is the case then a hole shot plate or different mounting location will fix your problem.
Your transducer mounting looks correct in that photo, so that rules out that problem. Let us know if you get it working!
Great job on the video showing the quality of your build! Looking forward to using one!
I leave mine on all the time; suspect it does use a little more power but I do not know this for a fact, nor does it concern me.
Frankly it looks like your transducer is weak. I would have thought a hard reset would have fixed it, but apparently not. If you have a different ethernet cable try that; also check all your...
Probably not the answer you wish to hear, but one to consider regardless; you can run both without crosstalk from the other, but only if you have one pinging and not the other.
Still useful to...