Thanks Kllr. Will ring him Monday.
Type: Posts; User: Crimson Tide
Thanks Kllr. Will ring him Monday.
Many thanks to all. I know now that my OptiMax 300 XS Stroker has a NON Damper FlyWheel that is actually in very questionable condition. Just to be very clear here I purchased a used but "very low...
Something in the range of 2010 +/- Mr. Simon was active in OptiMax tweeking. Anyone know how to make contact with him. Thanks in advance for any assistance you may provide.
Roll Tide Yall
OK, so I am back on the trail of this issue. Been recovering from a wreck. (Lost my 98 Wrangle TJ. Truly a family member.) So Cowl is off and I see a large plastic cover protecting the general...
At doc this AM, guy waiting to launch commented on my engine sounding as if the exhaust was removed?? Considering I have only had it in the water one other time and did not run it hard at all, I...
OK Don. So how can I determine if my flywheel has the damper and is it something that can be added to the unit I have if need?? Thanks much for the assistance??
Is the "3.2 Stroker" running a standard 300 OptiMax flywheel assembly or is it a specific model for the 300XS Stroker?
I have been considering the same. Not very far into the actual project but does not appear to be a major undertaking. Please share any info you come across and I will do same.
Have 300 XS sat for 16 months in storage. Will remove all fuel and replace with clean NEW 93 octane. What should I do to engine to insure it is properly prepared for start up, etc. Also, the...
Considering the service and sincerity I have enjoyed from BULLET, Tom, Matt and Teresa and I have NEVER purchased a NEW Bullet from them nor a dealer. However, I did ask them to treat me as if I...
Need to remove the rear air inlet wedge from my damaged cowl for repair and repainting damaged cowl. Please help?? I cannot figure out how to remove and reinstall it.
This post is old enough. How do I remove it. Thanks,
WV Bullet, I am hoping there is a complete switch kit. Otherwise I will look at separating the start-run function from the system power and aux.alarm and monitor circuits. Just kicking the tires as...
Completing refurb and repower my 21XD with 300 XS. New switch panel and switches helm and bow, new dash panel with new gauges and electronic's. And now in the last minute of the last hour I have...
931-762-0959 Tina Mann at Lawerenceburg Marine had several on the shelf last time I looked. Most were black and a couple were red as I recall. http://www.bassboatcentral.com/smileys/thumbsup2.gif ...
Hey!!! Orange Pride?????? Vol What???? Them Elephants ran into some ORANGE COWS out in California. Them cows went home with RED Tails!! OOOOOOHHHHHH, I missed your point!!!! You mean Rocky...
See general forum or Bullet forum for story. Ethonol killed it!! http://www.bassboatcentral.com/smileys/mad.gif http://www.bassboatcentral.com/smileys/mad.gif ...
I forgot to say, the reason the engine was struggling out of the hole and at high RPM was that it was starving for fuel due to the fuel line having crack in it.
Well boys and girls, this one is about the biggest kick in the ass I have ever taken. The engine went totally lean, melted #6 piston into three balls of aluminum, burned the other five past re-using...
Hey Judge,
I am finishing a 21XD that I went through top to bottom. The cap was B-A-D and I fixed a lot that some folks would have left alone!! Paul Nichols at Nichols Outboard Engineering did 90%...
2005 250 XS grenaded at 4800 crusing this Tuesday past. No warning or even a chance to shut it down. ONLY 189 hours total on the engine!!!
Hole large enough to put thumb through #5 in the...
Done! Thanks much. Gotta get the Tide to rolling again. Them large ole girls will be getting hungary over to Guntersville in about 5 weeks!!
Bama Bullet
Paul was and is a wealth of information. He has had a huge hand in rebirthing the Crimson Tide and I would never have been done without him. He will get the block i a couple days and we will know...
Hey Guys,
2005 250 XS that ran great on the Crimson Tide up until yesterday. Has a hole in the block I can put a finger through. No warning, just wham, it was dead. Was on plane around 4800-5000...
I need about a month to get all the bugs out! Then I am in for any meet anywhere. Guntersville AND Wheeler will be HOT for the big momma's mid to late Sept. We dove hunt the first two weekends and...