Search:

Type: Posts; User: mkm

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    744

    I went from a Fortrex to the Force 2 years ago....

    I went from a Fortrex to the Force 2 years ago. Bolt holes lined up. I hard wired the pedal instead of using batteries and it has worked perfect. Haven't had any problems with the Force, its been a...
  2. Replies
    0
    Views
    235

    Ionic 4 Bank Charger - Forsale

    SOLD...Don't need this since I bought a 5 bank. Will charge lead acid, lithium and agm batteries. Located in Benson, work in Raleigh. $200 obo

    532668
  3. Replies
    14
    Views
    922

    I have the Force with 2 100ah Ionics, 24v system....

    I have the Force with 2 100ah Ionics, 24v system. Charge every 5th or 6th trip. These batteries with the Force are great.
  4. Replies
    5
    Views
    302

    Hennessey Outdoor Electronics made one for me. ...

    Hennessey Outdoor Electronics made one for me. They can probably put the bird logo on it.

    530392
  5. Replies
    5
    Views
    365

    Mr. Don sells a kit that will have everything you...

    Mr. Don sells a kit that will have everything you need.
  6. Thread: 2020 618 pro

    by mkm
    Replies
    4
    Views
    464

    I have a 2019 with the 175 pro xs 4 stroke. The...

    I have a 2019 with the 175 pro xs 4 stroke. The only minor negative for me is the front deck is little narrow. Ride and storage is great. I added a Bobs JP and swapped out the manual plate last...
  7. Have no experience with the Ultrex, but went from...

    Have no experience with the Ultrex, but went from a Fortrex to the Garmin a year ago. Garmin TM has been a great motor so far.
  8. Replies
    13
    Views
    749

    I use the Range Technology disabler on a 2019...

    I use the Range Technology disabler on a 2019 vett and it's been fine.
  9. Replies
    13
    Views
    1,498

    I added the dual over the pedal mount, with a...

    I added the dual over the pedal mount, with a Garmin 10" and Humminbird 10", last March. I used ss screws and have been fine so far, other than having to re-tighten a couple of times.
  10. Replies
    39
    Views
    4,050

    At the beginning of the year, the Ultrex I was...

    At the beginning of the year, the Ultrex I was wanting/needing was out of stock everywhere, so I bought the Force. Its been a great motor so far.
  11. Thread: 2023 818 Pro

    by mkm
    Replies
    11
    Views
    1,296

    :thumb up2:, looks good

    :thumb up2:, looks good
  12. Don't forget to tape off the water pickup at nose...

    Don't forget to tape off the water pickup at nose of Lower unit, if your 150 has that.
  13. Replies
    4
    Views
    647

    I have 2 10s at bow and 2 10s at console. At...

    I have 2 10s at bow and 2 10s at console. At bow, I went with the over the pedal dual mount (Hennessey Outdoors). I just used screws and has been fine so far. Before this, I had single 12 mounted...
  14. Replies
    5
    Views
    544

    I have a 2019 618 with the 175 pro xs, Bob's...

    I have a 2019 618 with the 175 pro xs, Bob's plate. With a 23p Tempest plus, in the summer, I'm getting 5800-6000 rpm, 63-64 mph. With a 24p Tempest Plus, in cooler weather, 5800-5900 rpm, 66-67...
  15. I have a 175 hp doing the same thing but temp is...

    I have a 175 hp doing the same thing but temp is ok. Had the water pump replaced by merc mechanic after 3 yrs (less than 100 hrs) this past May. Wp was .5 - .8 at idle after a run with the new...
  16. Replies
    6
    Views
    505

    Shouldn't have any problems as long as you air...

    Shouldn't have any problems as long as you air down your tires (15-20 psi) prior to driving on the sand.
  17. Replies
    0
    Views
    264

    Garmin LVS32 Transducer Forsale

    LVS32 transducer only. Has shaft mount, barrel mount and prospective mount. 4 months old. $500

    497010

    497011
  18. Replies
    6
    Views
    505

    I usually go early spring and in the fall and...

    I usually go early spring and in the fall and fish at the point and off the ramps between Avon and Salvo. Beach is always changing so can't give suggestions on actual spots but the point is...
  19. Replies
    9
    Views
    396

    I replied to your email.

    I replied to your email.
  20. Replies
    9
    Views
    396

    Thanks for the info. I have a Phoenix and the...

    Thanks for the info. I have a Phoenix and the gauge that the MercMonitor, that I've seen replace, is the gauge that shows water pressure, voltage, fuel level and trim. Will the plug for my current...
  21. Replies
    9
    Views
    396

    Not sure why, I'm not familiar with these gauges....

    Not sure why, I'm not familiar with these gauges. I'll check out the Mercmonitor though.
  22. Replies
    9
    Views
    396

    Installing Mercury SmartCraft SC1000

    Serial number 2b637409

    Thinking about adding the sc1000 (79-879896K21) to console. Currently have the vessel view mob and would like to keep it installed. Other than the gauge, any other parts I...
  23. Replies
    128
    Views
    18,286

    Will do, I just looked up the part #, that you...

    Will do, I just looked up the part #, that you listed here, on Mercury's website and that part # is listed for my motor. I'll mark with a Sharpie.
  24. Replies
    128
    Views
    18,286

    Just read this thread, Don is this just for the...

    Just read this thread, Don is this just for the pro xs 250 motors? I have a pro xs 175 (2b637409) and wondering if this is something I need to keep a check on.
  25. Replies
    4
    Views
    296

    As others have mentioned, it's already maxed out....

    As others have mentioned, it's already maxed out. I wanted mine to have more tension also when I first got it. Gotten use to it now.
Results 1 to 25 of 189
Page 1 of 8 1 2 3 4