Mega imaging transducer on backwash plate on mine for a few yrs.,no issues,Y cable to the shoot thru puck,in the tray,built into the hull,works perfectly also
Type: Posts; User: cajunrgfm
Mega imaging transducer on backwash plate on mine for a few yrs.,no issues,Y cable to the shoot thru puck,in the tray,built into the hull,works perfectly also
In all honesty,I find my xb03 too narrow up front,from where I sit at troller,I actually have my pedal offset,to favor my right foot,
make sure it has the resistor spark plugs, or it will run like crap,
did you ever inspect or swap the steel reeds to carbon fiber ?
Agreed,I have found silly corroded engine mounted,and even pinched kill switch ground wires,and grounding bolts,caked in white powder, that a quick wire wheel clean up, made the ground contacts to...
Idle relief holes in the adapter plate, possibly plugged with carbon deposits
tks I ordered a 20T with the xtra shielding for trolling motors
I think i will look for the xtm with added shielding,the xtm 9 wide DI 20T should fine,as i do alot of drop shotting,mostly on a split screen 2d/chart for holding up on waypoints, an DI is nice now...
Ok tks,i did have alot of interference with my xnt up front,even after adding a ground wire from troller to batt. Ground. Tks
Wayne I found an xnt 9 t Di with RD transducer saver mount in classifieds,that should be good for me ?
tks Wayne,I already have mega SI on my transom,this is just my bow unit,which I really only use 2d/chart and 360
Does Xtm-9-wide-20 t ducer fit my 1159 HD DI ? HB's site only mentions the 1158di ,but says 1100 series. So, wanna be sure before i order it, other option i suppose is the "coffin" shaped unit, which...
On MG xi5 shafts i use west epoxy,1 time use shafts on them as well unless you keep the center section and replace the motor and card etc. Individually. It is cheaper to replace the foot as a factory...
The new foot comes ready to rock with enuff wire to work on a 60" shaft,they want $$$ for their special glue,i used west epoxy on the threads of my new shaft,and it's on for life
Mine died the same death,i found it cheaper to buy the whole foot already assembled,than to replace all the parts,which also involves a new shaft anyhow,the shafts are 1 use only,it wasnt all that...
is this an older style xri or newer style motorola motor ? tks
the ignition switch,keys,kill switch,power to dash guages,and alarm horn etc., all come with a new factory harness,the last one I bought was under $200,but was an 8 pin,20 footer is plenty in an 03,
the st. croix mojo bass are all purple
:beers:
a 225 promax head has different volume heads than a 175,,the CC's are dictated by the part# on the head,,most painted black heads can interchange ok,but gasket thickness and port volume will differ a...
prolly ok if power didn't get past the key switch,check the big fuse in the red holder on the powerhead,,,try to start,as suggested,I've seen the old inline 6's blow a switch box doing that,,
Is the liner inside the midsection ? there is just a rubber grommet inside the adapter plate that holds the copper tube in place,,from there when the lower unit is installed it is held in place by...
double check that there isnt any remnants of an older washer in the drain and vent plug cavity,causing the new seals to not seat properly,,I dont know if you have the proper socket,to make sure the...
I bought a 2500 chevy express,and just insulated it and set it up to pull my boat,and a place to crash overnight on weekends only,when i fish a few miles from home,,,I'm not a full time family...
you can get used to the Ram part,,it's the cummins and dana power train that's the best deal.