Yes, based on my research type A2 can be used for vent lines and fill lines.
I got lucky and found 5/8” type A1 from a local shop that had some remnants with lengths that worked for me. Thx for...
Type: Posts; User: kmelford
Yes, based on my research type A2 can be used for vent lines and fill lines.
I got lucky and found 5/8” type A1 from a local shop that had some remnants with lengths that worked for me. Thx for...
I may have found a source for type A1. They have some remnants they may be able sell me. I will likely go with Type A2 if it doesn't work out.
How do I test if it's broken wire without pulling apart the throttle control, which is a major event because access is very limited behind it?
Here's a pic.
548522548523
I'm struggling to find 5/8" Type A1-15 hose. Other sizes are available but not 5/8" (i.e. 3/8 and 5/16). I found 5/8" Type A2 hose which looks to be specifically for fill and vent lines. This hose...
Can the shifter switch be replaced and if so, are the available for purchase?
I have a 1997 Champion bass boat with a 175 EFI (0G361770). Over the last month the trim-up wouldn't work occasionally when on plane (under pressure) until a slightly backed off a little. I thought...
Thanks guys. I was able to find the faded lettering on the hose and it is 5/8" type A1. Seems like that hose is difficult to find.
Is there a special type of hose I should use when replacing my gas tank vent hoses? I didn't see any references to these hoses in the fuel system posts.
I have a 1997 bassboat and the hose is...
I’m trying to help a friend with his new Tracker (see model in title). It looks like it doesn’t have a primer bulb and most of the fuel line is within inaccessible areas. He has had several me...
Rick, How elaborate of a process is it to jack the boat up to install new bunks in the garage? Thanks.
Thank you for the feedback. I'm surprised to hear that some motors aren't installed square on the transom...... You would think the boat manufacturers would have a good process for this?
Thank you for the feedback. We've confirmed that the engine did come with the boat from the manufacturer. Have you ever seen an engine not installed square on the transom from the manufacturer?
It turns out the motor has one of those trolling spingloaded tabs connected to the lower unit. It stays behind the prop at low RPM's to slow the boat down for trolling purposes. When you take off...
I'm helping a friend find a boat to buy for casual fishing and other lake activities. He found a Crestliner with a 40 hp motor (s/n OT939377). When he took it for a test run it consistently leaned...
Thank you! That's an impressive process and report! The axle and suspension system has definitely changed for the better since mine was built in 2008. My spindles are more vulnerable to damage if...
It's good that you saw an issue before you had a real problem. I replace my bearings and brakes every two years and that timing has worked for me for the last 20 years. Unfortunately I had a...
Matty Wong is also with Bass Cat this year with a new STS Puma. He will be a good advocate for BCB!
Thanks guys!!! That is very helpful. With that info, my plan is to tighten things up for now and replace the bunks this later when our lake levels are higher here in so cal. Right now there isn’t...
Has anyone replaced their bunks that can provide some feedback on what you found? For example, how many years did you wait, what were the condition of the bunks, could you have waited or should you...
Hi all. I have a 2008 Puma I bought new and I still love my boat and I'm on the water with it about two times per month on average. I have two boats, so I'm on the other one about every other week...
After covering the openings, I put a large unused plastic trash bag over the motor. I didn't want to place the cowling back on in case it was dirty or I would hit something by mistake.
I may have missed this in some of the responses above, but, have you pulled the screws holding the cable management sleeve at the front? I just worked on mine and this helped me.
Thanks guys! I have a feeling that I put some pressure on the that fitting a few years ago when reinstalling my injectors after I had them maintained. Also, the O-rings on that side got damaged in...
Makes sense. Hopefully the other fittings hold up. Do you guys have a recommended change out of parts at a certain time point (hours or age)? If so, is there a kit of parts available?
Boat ran great and no fuel leaks. Thx again Don