Thank you them look more reasonable priced I will get some and give them a try
Type: Posts; User: Greenhotshot
Thank you them look more reasonable priced I will get some and give them a try
Hey guys wanting to try my hand at catching some crappie with jerk baits most everyone is saying they are using the megabass oneten jr I am having a hard time cutting loose of enough money to buy one...
Hello everyone I have just bought a 2021 z21 love it so far just have one problem. It is a 21 so it has the three compartment door in between the 2 rod boxes on the front deck so the problem is the...
I have left it off the charger for a day and the voltaged was between 12.6 and 12.7. I appreciate the suggestion on the battery i will look into that battery and also into lithium. I do hate the...
My cord did have a ground and I switched and tried a different cord to. So I guess I’m out of ideas interstate just told me that their battery warranty only cover their batteries that won’t hold a...
Thank you I will check my cord tomorrow when I get to my shop and see it may not have a ground. I will update later thanks
I would just say make sure you do it right I tried to get away from onboard because had one go bad and didnt want to pay to replace it. Burnt my boat up in hotel parking lot trying to charge with...
Thanks I had done that though I have the battery out of boat nothing hooked up but the charger
I have a AGM start battery around 1 1/2 years old and i have a noco 10x4 charger the AMG battery never shuts the charger off it will charge for days if I would let it. the banks on my trolling...
thankyou i checked and my software now is 3.9 something so I am picking up sd card tonight and i will put update on tomorrow and see how that works out for me I will update thanks again for the info ...
I bought a boat with a 10” and 12” solix gen 3 on it and I have added my 360 non mega from my old boat I can not get it to work. When I turn it on it gives me the 360 view and I open it up it shows...
So to measure my p2p I ran a straight edge about 4 or 5 feet up against the pad up under the boat and leveled it then leveled the plate on the motor then measured from the top of my straight edge to...
The lower unit says it is the 1.75 it is the silver one does that tell you what lower unit it has. Had it out this weekend tried to do a little measuring so the best I can tell by what I think I’m...
I have had three different props on it. It came with a 31p prop I went to a prop shop and ran some different props on it just for a pass or two the 25 tempest seemed to preform the best of them so I...
It is a 10” manual jack plate not really sure what a heavy ultrex motor is but it has a 250xs racing motor 2003.
I’ve had the issue as long as I have owned the boat about 2 1/2 years. I haven’t been able to find any cracks in the hull but I will look it over again. That rpm reading was on a digital smart craft...
So I’ve been dealing with a lot of problems with my gambler all the way to putting in a new power head. Everyone has told me I’ve got motor problems but nothing has seemed to help it has a 250...
I will probably be looking for another marina I guess so I will see if they can do them test you recommended. I am sure about the plugs because it is a different number that is on my motor tag I did...
It is a brand new prop and I’ve tried 3 different ones all of which had that much slip. Before the new power head the problem seemed to be on cylinder 6 since the new one it’s fouled plugs on three...
It is a 1994 gambler. Every time I have taken it to marina they have told me fuel and air pressure is good and they claim they have checked compression and it is fine which I would think they would...
2003 250xs L racing
s/n OT652652
25 tempest, rpm 5850, water pressure idle around 2 and wot around 16
smartcraft gauge and gps top speed around 58mph
I appreciate your time looking at this I...
Just a little update had our crappie camp last weekend took boat out to do some fishing thought I would keep track of some numbers see if anything changed. It ran good for 3 days didn’t go very far...
So when I’m at WOT trimmed mostly down it will have around 15 psi or a little more I will keep trimming it a little at a time and watch the rpm and speed until water pressure gets down around 8 or 9...
I ran it for 1 1/2 hours playing with trim doing everything I could to try to make it better. The mph are from gps and the rpms are from digital mercury smart gauge. Prop to pad is between 3 and 3...
Thanks for the input guys I guess as much as I hate to I will have to take it to the marina to get the motor checked out it just takes so long to get anything done around here they are all so busy...