I have a Z519 and my father has a 198P. We both run Ionics dedicated to electronics and TM. 1 - 125ah running 4 - 12" HDS Lives and Active Target, 3 - 50ah to power the Ghost. Never an issue with...
Type: Posts; User: Braxtonta
I have a Z519 and my father has a 198P. We both run Ionics dedicated to electronics and TM. 1 - 125ah running 4 - 12" HDS Lives and Active Target, 3 - 50ah to power the Ghost. Never an issue with...
Here's a dual BBT mount on a Z519 with Ghost TM. The mount is NOT the off-set option but rather I off-set the top gimbal bracket when mounting. The off-set option would interfere with the trim...
Stratos295pe - I also run a Z519 w/ProXP 225. Currently, with a 24P Fury 4 (no plugs) and can turn it 5800 (69-71mph) loaded with equipment, fuel, and me. Haven't really played much with the P2P...
I have experienced the same. Re-calibrated the Point 1 and it didn't help. I went into settings to ensure that Point 1 was listed in the network, yes! I went to data sources for Heading and the...
Make sure your 2D sonar is not STOPPED. You symptoms indicate that it is. You should also see the same slow and choppy scroll speed in downscan as well as sidescan.
Marc - I really appreciate you're willingness to create these videos to help. If a hard reset is what is "required" it seems that Lowrance would have communicated that along with the update...
Mach440 - Let us know how the rollback goes.
Unplug the power cable from the units, wait a few minutes, re-apply power and try again.
Does anyone have this AT update? ActiveTarget-22.1-65.1.14-Standard-1.riw
I was able to find the 20.1 version that I have saved but not the 22.1.
I was also able to find the 22.1 for the HDS...
523151
Me!
523149
In my opinion. Mount it on the stern. I mounted mine on the pie shaped carpeted area on the driver side. Be sure to change the source for GPS on any console mounted Lowrance unit to use the Point 1....
The attachment link will not open a photo.
Eric, I received my order and installed yesterday! These guards look great and I am so glad that I ran across your post. Thanks for your forward thought and ingenuity with this product :salute:....
Check the rub rail seal.
Try Great Lakes Skipper, they have replacement panels.
https://www.greatlakesskipper.com/search/?q=ranger+dash+panel
Good to hear and I know you'll be happy to get it out on the water. If you remember, get back to me with your numbers with that 23P Fury 3. It looks like our set-up is about the same.
I am pretty sure that there will be a reduction of what I can spin the 24p Fury 4 once the NC heat and humidity hits. Therefore, I'm thinking that the 23p or 24p Fury 3 may be the summer prop....
I only remember one tube extending between the console and the bow. Wmitch2 is correct as there is another tube that runs from the bow but ends at the starboard side (built-in) navigation light....
Thanks, I was thinking that I needed to prop it out so I could spin get the 6200 rpm.
What are some recommendations on setting up a Z519 w/ProXP 225? Currently, I have a 24P Fury 4 and can turn it 5800 (69-71mph) loaded with equipment, fuel, and me. Haven't really played much with the...
I don't have 16s on the bow..........but if I did, they'd be mounted on BBT mounts with the Warrior Series gimbals! :thumb up2:
My father has a '20 RT198P. I installed BBT mounts on the console and bow at his request. Also, installed a battery switch in the rigging compartment powered from a 125ah Ionic to "only" power 4-12"...
#11Today, 08:32 AM
I just last weekend installed Ionics, 3-50 ah (Ghost TM) and 1-125ah (dedicated to electronics) batteries in my '22 Z519. I left the group 31 AGM in place for cranking, pumps,...
I just last weekend installed 3-50 ah (Ghost TM) and 1-125ah (dedicated to electronics) batteries in my '22 Z519. I left the group 31 AGM in place for cranking, pumps, and lights.
513633