Search:

Type: Posts; User: Jasay

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    357

    Do you know of a way to bleed this thing? All I...

    Do you know of a way to bleed this thing? All I found was 2 aluminum flat head screws but couldn't get them to budge.
  2. Replies
    6
    Views
    357

    BTW you can hear the motor running when you press...

    BTW you can hear the motor running when you press the switch so, I know it is getting power...
  3. Replies
    6
    Views
    357

    Atlas Jackplate won't go up or down

    Ok so, I had some seals blow out on my Atlas Jackplate Hydraulic. I ordered a seal kit from TH Marine and replaced the blown seals (not all). Added fluid straight to the cylinder chamber and put...
  4. Replies
    31
    Views
    1,175

    I'm no expert on these motors but I am a...

    I'm no expert on these motors but I am a mechanical designer/drafter/Reverse engineer(/whatever needs done, 😂) at a heavy industrial machine shop and deal with things similar to this all the time....
  5. Replies
    33
    Views
    1,379

    If you look carefully at the exhaust port in the...

    If you look carefully at the exhaust port in the upper portion of the photo, there is a chunk of the sleeve missing near the end of the sleeve
  6. Replies
    33
    Views
    1,379

    Took the head off today to inspect the cylinder....

    Took the head off today to inspect the cylinder. Part of the sleeve below the exhaust port broke off and beat around inside the cylinder.

    534538
  7. Replies
    33
    Views
    1,379

    I've been running the quicksilver premium plus.

    I've been running the quicksilver premium plus.
  8. Replies
    33
    Views
    1,379

    Does anyone have any recommendation on a rebuild...

    Does anyone have any recommendation on a rebuild kit? I'm going to start checking fuel pumps and everything I can to see what caused this. Will know more today what the actual damage is, I'm...
  9. Replies
    33
    Views
    1,379

    Ok, worse info. I compression tested the...

    Ok, worse info.

    I compression tested the engine. In order, 115, 105, 115, 115, 115, 0.

    I have a boy on high-school fishing team, need to be back on water by December 2 (next tournament). What...
  10. Replies
    33
    Views
    1,379

    That's what I'm using dual guages, glycerin...

    That's what I'm using dual guages, glycerin filled

    They may not be the best but this is them.
    https://www.harborfreight.com/230-psi-14-in-npt-filled-gauge-64558.html

    On this setup...
  11. Replies
    33
    Views
    1,379

    Update! I checked out what I could today....

    Update!

    I checked out what I could today.
    Air pressure: 85
    Fuel pressure: jumping between 100-105
    Checked coils, all good. But,
    No change when unplugging #6 coil. Tested for spark and I am...
  12. Replies
    33
    Views
    1,379

    Yes I'll definitely be getting all this done. My...

    Yes I'll definitely be getting all this done.
    My only question is, would this cause the engine to not Rev up enough to get on plane?
  13. Replies
    33
    Views
    1,379

    534295534296 Not good. Will that cause the...

    534295534296

    Not good. Will that cause the knocking sound?
  14. Replies
    33
    Views
    1,379

    This weekend, I'm going to disassemble my...

    This weekend, I'm going to disassemble my compressor, while leaving most of it on the motor, and check out the crank bearing and crankpin. I'm going to see about what I can do, as far as going ahead...
  15. Replies
    33
    Views
    1,379

    While I'm at it I better check the reeds

    While I'm at it I better check the reeds
  16. Replies
    33
    Views
    1,379

    534105 These...

    534105

    These...
  17. Replies
    33
    Views
    1,379

    Only way to check that bearing is going to be...

    Only way to check that bearing is going to be disassembly right? That is the bearing the compressor piston rides on right?
  18. Replies
    33
    Views
    1,379

    I'm not sure. I purchased the boat 2 years ago....

    I'm not sure. I purchased the boat 2 years ago.
    mechanic checked it out last year and said everything was good though.
  19. Replies
    33
    Views
    1,379

    Pressure was fine a couple weeks ago..

    Pressure was fine a couple weeks ago..
  20. Replies
    33
    Views
    1,379

    https://youtube.com/shorts/8yaZs7zeJn0?si=a-8AZ15F...

    https://youtube.com/shorts/8yaZs7zeJn0?si=a-8AZ15FXdiyUxxl

    https://youtube.com/shorts/E2BMMHmThMo?si=qV8b3KKUthUIgvaH
  21. Replies
    33
    Views
    1,379

    250 pro xs help again please.

    We had a tournament last Saturday and the engine ran fine up until time to come back in. Luckily I wasn't far from the ramp.

    When I started her up to head back to the ramp she had what seemed...
  22. Replies
    1
    Views
    208

    Slap Latches for 08 TR21x HP

    Has anyone here had any luck converting your deck lid locks to slap latch style instead of the twist and pull latches? Looks like the hole may need to be welded up and cut closer to the edge of the...
  23. Replies
    7
    Views
    573

    If you made the Cad file for this send me a pm

    If you made the Cad file for this send me a pm
  24. Thank you. That was going to be the first panel I...

    Thank you. That was going to be the first panel I pulled. Justin wanted to make sure before having to go through the trouble and it not be it.
  25. Looking for Livewell repair information 08 TR21X HP

    My TR21X HP has a leak on the starboard livewell & the Port Livewell needs a new aerator nozzle. What is the best way to get to the plumbing for them?

    Thanks in advance
Results 1 to 25 of 77
Page 1 of 4 1 2 3 4