Is the correct setting in a helix 10 Gen 2 - DI 200/455 khz for the trolling motor down Imaging transducer. ?
Is the correct setting in a helix 10 Gen 2 - DI 200/455 khz for the trolling motor down Imaging transducer. ?
Depends on which trolling motor DI transducer you have.
XTM 9 DI 25 T is DI 200/455 kHz
XTM 9 WIDE DI 20 T is DI 83/200 kHz
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Xtm 9 mdi t
That's a Mega transducer. Should be a selection for Mega Transducer. That's what mine says.
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
I have a mega si \di but i dont see a setting for the mega di by itself , it includes mega si di
Last edited by Wayne P.; 03-15-2019 at 06:22 PM.
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Connected transducer choices are Mega Imaging, compact Side Imaging , high-definition Side Imaging, HB 50/200 khz + 455 khz SI, di 200/455khz , di 83/200khz , di 50/200 khz and some more that i know would not go with this unit. I have not updated my unit because it runs fine the way it is and I know it with the new update there are a couple of issues but it's version 1.6
Software version 1.830 makes the unit compatible with the Minnkota MDI transducer and the transducer you have.
If you want to use that transducer, you have to install the software that allows it.
The software date is September 12, 2018.
New Features:
· HW CHIRP Transducer Support [CHIRP ModelsOnly] – Connected Transducer modes now include a High Wide CHIRP Mode, called“HW CHIRP”. This allows MEGA DI and Built-In MEGA DI transducers to be usedwith 2D models or without DI pinging.
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Ok can i use the mega imaging setting for just viewing 2d this weekend even tho it wont be mega till i update ?
You already have MEGA Imaging. It's the Dual Spectrum CHIRP 2D sonar you don't have (that HW thing).
You can leave it at the default setting and it should do maybe OK using 200 kHz and still have 455/800/1200 kHz Down Imaging.
OR you can turn off SI by using DI 83/200 kHz and loose 1200 kHz DI and still use 200 kHz 2D.
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
I have the same transducer and the same unit as stated above. I’ve updated mine and still only shows the first mentioned.
i updated from 1.6 to 1.9. The boat had been in storage since November
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Now I'm confused! Lol!
I believe the OP had prior posts on having H10 MEGA SI models but using the XTM 9 MDI MEGA DI transducer on the TM. Not a normal setup but maybe just temporary. The connected transducer setting needs to be changed anytime you use a transducer other than the standard transom or TM version transducer for the model.
Wes
Helix 10 MSI+,MDI+,Ultrex IPilot
2023 Phoenix 818
Never assume there's a tomorrow
No i have a g2 mega unit i just want the mega di on the trolling motor and use my other mega unit to share gps and si . In order to make my unit compatible with mega di as Wayne said I have to upgrade my unit to 1.8 if I want to use the xnt 9 MDI T transducer.