New Thru Hull fittings

[Jdwelding]

I have my bilge tore apart. Where can I get the correct ones? I need the 3/4 for the livewell drain and the 1 1/8 for the over flow.
I ordered from Flow- Rite because I needed a few other things and not only are they too short, but the 1 1/8 is way too large. The flange measures 2.235" and the threaded part is 1.42.
I just had to cancel an order from TH Marine because that threaded part they say is 1 3/8.
I need a correct length 3/4" black straight and a black 1 1/8". The threaded lengths are 2" and 2 1/4". The hole in my hull measures 1.350
The threaded part on the broken one measures 1.277 and the flange measures 1.825.
I can't believe there's no standard on these for diameter.

[Ed R]

https://store.flow-rite.com/products...-fittings.html

https://store.flow-rite.com/products...-fittings.html

[Jdwelding]

https://store.flow-rite.com/products...-fittings.html

https://store.flow-rite.com/products...-fittings.html

Lol,
You must've not read my post. They are wrong

[grout-scout]

https://www.jamestowndistributors.co...+hull+fittings


lots to go through, I used the SS ones.

[Jdwelding]

https://www.jamestowndistributors.co...+hull+fittings


lots to go through, I used the SS ones.

The sea choice may work but there's no drawing. I could run into the same problem with the previous 2 orders.

[grout-scout]

You know who you might call is Carol at C & O Marine, they used to be a big Champ seller/servicer. She just might have what you need, you’ll have to call though their website doesn’t show inventory anymore.

[Jdwelding]

You know who you might call is Carol at C & O Marine, they used to be a big Champ seller/servicer. She just might have what you need, you’ll have to call though their website doesn’t show inventory anymore.

This shouldn't have to be such a chore lol

[grout-scout]

This shouldn't have to be such a chore lol

You wouldn’t think it would be! Lol

I didn’t have any issues, not sure what year you’re working with though.

[Jdwelding]

You wouldn’t think it would be! Lol

I didn’t have any issues, not sure what year you’re working with though.

I guess I should have put that! It's a 95 190

[Ed R]

Lol,
You must've not read my post. They are wrong

I skipped the important parts....

[Jdwelding]

Well I sent C&O an email. I still can't believe there isn't a standard for these things.

[rond13]

Here are the ones I used for my 1990 Champion 184

https://www.ebay.com/itm/Perko-3-4-T...-/252023544648
https://www.ebay.com/itm/Perko-1-1-8...item5421aa6423

[Jdwelding]

Here are the ones I used for my 1990 Champion 184

https://www.ebay.com/itm/Perko-3-4-T...-/252023544648
https://www.ebay.com/itm/Perko-1-1-8...item5421aa6423

I think Perko might have been the OEM, but I want the black plastic ones. Can't find them.

[86 inches]

Great Lakes Skipper will have what you want. They list all dimensions of most of their thru hulls so you can be sure that you’re getting the right part. They deliver quickly.

The black plastic fittings suck but whatever. They have those too if you’re dead set on using them.

Here’s a thread that might help
http://www.bbcboards.net/showthread....+hull+fittings

[Tx Champ]

Well I sent C&O an email. I still can't believe there isn't a standard for these things.

You need to call them and talk to Carol, not e-mail. They're not too good at answering e-mails. Remember you have a 23+ year old boat. The OEM fittings were barbed Flow-Rite, and they have since phased out all of their barbed fittings. Places like Great Lakes Skipper are good for older parts.

Good Luck!

[1bluemcm]

Great lakes skipper. Went stainless as well.