I made a few the other day and they work very well although I'm going to change the design a little bit to make it easier on Machining and the end-user. I will update when I get the new ones made.
I made a few the other day and they work very well although I'm going to change the design a little bit to make it easier on Machining and the end-user. I will update when I get the new ones made.
Last edited by bassmastrbw96; 08-11-2018 at 04:49 PM. Reason: Design change
No more pulling a gas tank over a broken plastic arm..
Want to buy old river2sea bully wa frogs.
I might need one of those ....
Last edited by crank68; 08-10-2018 at 05:52 AM. Reason: Uneducated
BULLET 20 XRD/250 Merc Sport XS
www.ncboatguy.com
Bullet should pay you for those, I'm like Ted, I want one, great work!!
Well I have been meaning to make one for a while. I'm going to work on the upper arm today where the actual handle is at.
Nice work...
Marks Props 317-398-9294, 1850 East 225 South, Shelbyville, Indiana 46176 propellerman59@gmail.com http://www.marksprops.com/index.html
That's the ticket! The whole dang valve assembly should be aluminum.
In fact my new one just broke today ..... I’ll send you a check for one immediately !!!
BULLET 20 XRD/250 Merc Sport XS
www.ncboatguy.com
Crank breaks his all the time cuz of the BIG fish that go in his live well!!
Pm sent
Last edited by bassmastrbw96; 08-10-2018 at 08:46 PM. Reason: Pm
"LIKE"
20XDC Bullet/Modified Merc 260
295TF Charger/Merc 225X-Sold
20' Contender Pickle Fork/Merc EFI Bridgeport-Sold
18' Stratus with Sommerford Tunnel Vee Hull/2.4 EFI Merc High Perf-Sold
Freedom 240DLX Toon/Merc 115
10' Cougar Cub/Merc 25 on the Bottle
18" Homebuilt Tunnel/.021 OS Max Outboard on 50% Nitro with a Pipe
I'd like to see an aluminum housing with teflon seals to go with it...or just use a teflon ball to seal the ports!!!
You know alot of these valves and pumps wouldn't freeze and crack if they had a way to drain'em other than compressed air. Most peeps won't take the time to blow everything out when Winter sets in, they just run'em till the water stops coming out and that's not enough!
20XDC Bullet/Modified Merc 260
295TF Charger/Merc 225X-Sold
20' Contender Pickle Fork/Merc EFI Bridgeport-Sold
18' Stratus with Sommerford Tunnel Vee Hull/2.4 EFI Merc High Perf-Sold
Freedom 240DLX Toon/Merc 115
10' Cougar Cub/Merc 25 on the Bottle
18" Homebuilt Tunnel/.021 OS Max Outboard on 50% Nitro with a Pipe
Yeah I know what you mean. I'm honestly surprised they haven't put a ball valve or a gate valve in line and put an electric actuator on it so you can push a button. I have contemplated relocating the valve anyways because where it's at it's hard to work on.Originally Posted by QuickBullet
I tried putting the value on the other side, couldn't make it work
I haven't looked so I didn't know if it was an option or not. I broke two arms in one week so I am definitely going to resolve the issue.
Mine would have worked but the holes were cut to close to the center support or stringer, and I think I would have needed a longer cable, I was trying to upgrade my live well pumps and couldn't make it fit on the passenger side, that's why I tried
Prolly more along the lines of I’m a little heavy handed. When I put the new valve and selector at the top I actually put everything together loose to insure the cable wouldn’t bind....still broke. HA HA HA !!!
BULLET 20 XRD/250 Merc Sport XS
www.ncboatguy.com
Reply With Quote
.jpg)