Anyone know if this puck can be mounted upside down? I am contemplating mounting one under the bilge lid. Wondering if anyone has tried this or knows if it will or won’t work?
Anyone know if this puck can be mounted upside down? I am contemplating mounting one under the bilge lid. Wondering if anyone has tried this or knows if it will or won’t work?
2019 Basscat Caracal
225 Evinrude G2
Solix 12 Mega SI bow and console
Mega Live
36V Ultrex
I've seen videos where guys do mount it upside down.
Console [HELIX 10MSI G3N || HELIX 10MSI G3N]
Bow [HELIX 12 CHIRP SI GPS G2N] || RC-2] || [HELIX 10MSI G4N] || [M360 UNIVERSAL MOUNT] || [Mega Live]
ULTERRA80/US2/IPLINK-60" BT || 2xAS ETH 5PXG || Victron IP67 12V/25A || [NoCo Genius GX2440 24V/40A]
[X2 GROUP 31] x 3 || [Battleborn 31 lithium]
Alumacraft Voyageur 175/Yamaha VF115LA
absolutely NOT upside down. Bob
At the very least you will have East and West swapped. Most heading sensors(if not all) will not give you correct readings at all upside down.
Last edited by bobcoy; 04-17-2018 at 08:47 AM.
2019 Basscat Caracal
225 Evinrude G2
Solix 12 Mega SI bow and console
Mega Live
36V Ultrex
Just edited my post.
Not to hijack but is there interference issues from mounting a as gps hs puck next to the ultrex heading sensor?
Nitro z21
Not from each other but with the ultrex stowed,(out of the water) the sensor will have magnetic problems with the motor. Not an issue with the minn kota sensor as it is only used with the TM in the water. The HS- GPS will be used with the TM stowed I would assume.(use double faced tape to hold it temporary to try it) Bob
The Minn Kota Heading Sensor Instructions (2394900) also states (ref pg 2) "e. Mount the Heading Sensor horizontally. It should not be mounted upside down."
Wes
Helix 10 MSI+,MDI+,Ultrex IPilot
2023 Phoenix 818
Never assume there's a tomorrow
Ok. Thanks for the responses guys.
2019 Basscat Caracal
225 Evinrude G2
Solix 12 Mega SI bow and console
Mega Live
36V Ultrex
I installed my new Ulterra last weekend and placed the blue tooth heading sensor beneath my driver's console right side up. It paired fine and I am hopeful the location works well. I have two GPS pucks already-one from the Evinrude and one from 360. I really didn't want another visible puck.
GPS pucks need a view to the sky. A heading sensor doesn't.
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Nothing for me, but it provides SOG to the ICON gauge:
http://www.continuouswave.com/whaler...CONgauges.html
Wayne Purdum
Charlottesville, Va.
Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
MEGA LIVE, LIVE TL
Thanks guys dealer installed heading sensor in rear of boat. I told them I wanted 2 Hs gps pucks also one at bow and one at transom for in hull transducers. For some reason they installed one of the pucks at the console which serves no purpose. When I called them out on it they said it was do to interference from the ultrex heading sensor. It sounded like bs.
Nitro z21
There may have been interference but doubt from the heading sensor. You can test the location with a compass to verify.
Wes
Helix 10 MSI+,MDI+,Ultrex IPilot
2023 Phoenix 818
Never assume there's a tomorrow
Would a 15* tilt or close, starboard to port, cause problems with the accuracy of the gps heading sensor on the transom? I want it close to the transducer and preferably not on the rear deck to be tripped over. Thanks
Try it taped down and see if it will. The cable just laying on the deck. If it works ok screw it down and run the wire where you can. Bob