Any Z7 owners out there have an Ultrex mounted on their bow?
If so can you post a picture of the mounted base? I am getting an Ultrex and trying to get an idea of how much space the footprint will take up.
Many thanks
Any Z7 owners out there have an Ultrex mounted on their bow?
If so can you post a picture of the mounted base? I am getting an Ultrex and trying to get an idea of how much space the footprint will take up.
Many thanks
Always "Huntin" the IA Bass!
Boat: Nitro Z7
Primary Propulsion Unit: 200 Optimax ProXS
Vertical Depth Propulsion Adjustment: 8" Bobs Action Jack
Underwater Surveillance: Solix10 G2 Console & Solix10 G1 Bow
Anchoring: Powerpole, Ultrex Spot Lock
Dynamic Positioning System: Ultrex i-pilot Link
I found this picture from one of the Japanese Nitro dealers which illustrates an Ultrex on a Z7 that may help.
Thanks
Trying to get an idea on where the footprint will lay so I can plan a few thing ahead.
Looks like they have the shaft out quite a ways from the rub rail...
Always "Huntin" the IA Bass!
Boat: Nitro Z7
Primary Propulsion Unit: 200 Optimax ProXS
Vertical Depth Propulsion Adjustment: 8" Bobs Action Jack
Underwater Surveillance: Solix10 G2 Console & Solix10 G1 Bow
Anchoring: Powerpole, Ultrex Spot Lock
Dynamic Positioning System: Ultrex i-pilot Link
no. required some cutting
this is how much I cut
What if you move the plugin and push the pedal all the way forward?
I read it might fit then?
Always "Huntin" the IA Bass!
Boat: Nitro Z7
Primary Propulsion Unit: 200 Optimax ProXS
Vertical Depth Propulsion Adjustment: 8" Bobs Action Jack
Underwater Surveillance: Solix10 G2 Console & Solix10 G1 Bow
Anchoring: Powerpole, Ultrex Spot Lock
Dynamic Positioning System: Ultrex i-pilot Link
Always "Huntin" the IA Bass!
Boat: Nitro Z7
Primary Propulsion Unit: 200 Optimax ProXS
Vertical Depth Propulsion Adjustment: 8" Bobs Action Jack
Underwater Surveillance: Solix10 G2 Console & Solix10 G1 Bow
Anchoring: Powerpole, Ultrex Spot Lock
Dynamic Positioning System: Ultrex i-pilot Link
Just installed an Ultrex on my 2015 Nitro Z7. The pedal will not fit unless you ether cut the existing deck or the front panel ad run the cable strait out.
I have photos but they will not allow me to upload!!!
See my post on the 3rd page of the below
http://www.bbcboards.net/showthread.php?t=765934&page=3
And here. Can order the same tray and it should fit the z7
http://www.bbcboards.net/showthread.php?t=885754
Don't worry Ma'am....
I'm only here for the Bass.
Spotlock is not a problem as it sits higher. The other buttons are low and are not able to hit with foot. Dawson at fish on Fabrications can adjust the depth of the tray for you no problem.
I was more concerned with having the foot pedal be almost level with the deck than the two bottom.buttons. Spotlock is what I use the most and it's easily pressed with the foot.
I have a Z-7 and just installed my custom tray from Fishon to accommodate the Ultrex. It was the same design done for all of the Z-8s sporting new trays. It was perfect and Mjgarret is right, Dawson at Fishon will make it whatever depth you like. It did take a few weeks to get the tray as the powder coater was backed up but all in all, it was a good decision for me. I would highly recommend Fishon Fabrications. I will post some pics of my new setup when I get a chance.
Last edited by remaly181; 04-02-2018 at 09:17 PM.
ComforTroll
The foot pedal will fit once you move the plug. That's all I did, and it works great.