Results 1 to 5 of 5
  1. #1
    Member
    Join Date
    Apr 2017
    Location
    Colleyville, TX
    Posts
    575

    2017 Tracker PT 190TX ACC switch and wiring???

    I am trying to figure out the fuse panel/wiring on my Tracker 190TX. There are two terminals marked ACC. I believe one is supposed to run through the ACC switch on the dash and connects to the pigtail behind the dash panel. Where does the other ACC terminal go? Flipping the ACC switch does not appear to turn anything on or off unless its connected to the ACC pigtail.
    My friends 2017 PT 175 has the same two ACC fuse panel labels.
    Confused
    Joe B

    2017 Tracker PT 190 TX
    2017 Mercury 115 Pro XS
    Mercury Spitfire X7 19” prop
    51 mph @ 6240 rpms (RPMs from Vessel View Mobile) : full fuel tank and fishing load by myself
    4.2 second Hole Shot (measured using Vessel View Mobile)
    Engine mounted in 3rd hole
    Minn Kota Ulterra-Link w/built in MDI 80 lb thrust 60” shaft
    Humminbird Helix 12si Gen1 chirp on console
    Humminbird Helix 15si Gen4 cho on bow
    Humminbird Mega360

    Dotline two step transom boarding ladder
    Tracker trailer bow boarding step

  2. Member
    Join Date
    Jan 2005
    Location
    Texarkana
    Posts
    18,962
    #2
    If you're looking / asking about the fuse panel, most mfgs. will mark an empty slot as ACC, meaning that when you add accessories, you can connect to the spade terminal corresponding to that fuse and insert the fuse of the size you need.
    BBC Sponsor since 2006: (870) 773-3474
    Mon - Thrs 8am - 5pm Central
    Friday 8am-12pm
    Garmin Certified Dealer and Installers: Call us for all your Garmin Electronics needs!
    ASC for: Garmin, Lowrance, Minnkota, Humminbird, and Powerpole.
    [SIGPIC] http://www.jonestrollingmotor.com
    [/SIGPIC]

  3. Member
    Join Date
    Apr 2017
    Location
    Colleyville, TX
    Posts
    575
    #3
    Thank you for your response. I will look at the fuse panel again but that makes sense.
    Joe B

    2017 Tracker PT 190 TX
    2017 Mercury 115 Pro XS
    Mercury Spitfire X7 19” prop
    51 mph @ 6240 rpms (RPMs from Vessel View Mobile) : full fuel tank and fishing load by myself
    4.2 second Hole Shot (measured using Vessel View Mobile)
    Engine mounted in 3rd hole
    Minn Kota Ulterra-Link w/built in MDI 80 lb thrust 60” shaft
    Humminbird Helix 12si Gen1 chirp on console
    Humminbird Helix 15si Gen4 cho on bow
    Humminbird Mega360

    Dotline two step transom boarding ladder
    Tracker trailer bow boarding step

  4. Member Wayne P.'s Avatar
    Join Date
    Jan 2010
    Location
    Charlottesville, VA
    Posts
    30,444
    #4
    Quote Originally Posted by joe3buck3 View Post
    Thank you for your response. I will look at the fuse panel again but that makes sense.
    PM sent
    Wayne Purdum
    Charlottesville, Va.
    Helix 12 CHIRP MEGA+ SI G3N/G4N, Helix 15 CHIRP MEGA SI+ GPS G4N
    SOLIX 12 SI/G3, Helix 8 CHIRP MEGA SI+ G4N, Ultrex 80/LINK, MEGA360,
    MEGA LIVE, LIVE TL

  5. Member
    Join Date
    Dec 2015
    Location
    Alabama
    Posts
    21,605
    #5
    I am pretty sure that is an unused switch for you to add a circuit. Post in the tin boat section for an answer or call your dealer.