This is the second time in 3 yrs that I have spunned the drive sleeve on my tempest fury 25p. What's going on? Motor is a 2005 200 Yamaha vmax. Do I have the wrong thrust washer on wrong?
This is the second time in 3 yrs that I have spunned the drive sleeve on my tempest fury 25p. What's going on? Motor is a 2005 200 Yamaha vmax. Do I have the wrong thrust washer on wrong?
What torque specification are you using for the prop nut?
That may be the problem....i just tighten all the way and back it up to fit pin in. What is the torque spec supposed to be? The nut was pretty loose when I went to take the prop off
55lbs
I do believe when a new delrin sleeve is installed, you are to torque to 105#.
No the 100 lbs of torque is only used if the forward cone bushing is used and the Yamaha doesn't use it.
Marks Props 317-398-9294, 1850 East 225 South, Shelbyville, Indiana 46176 propellerman59@gmail.com http://www.marksprops.com/index.html
I don't know why Mercury doesn't put it in the other kits that are for the heavier props since it also helps support the front of the prop on the shaft and that would stop some of the wobble too.
I run the forward cone bushing on my Yamaha. I like the extra support and also being able to put more lbs/ft on the nut to make sure everything stays tight. Loose hub is what ruins thrust washers by allowing them to wallow out
2021 Phoenix 920 Elite / SHO 250
Bullet 21XD / 250 XB (Gone to a great home in LA)
"There is no such thing as a bad day fishing!"
So I ordered a new flo-torq II hub kit. Now do I use the thrust washer that's included or do I stick with the Yamaha thrust washer. The Yamaha thrust washer has a rounded edge compared to the flat thrust washer included in the kit. Last time I just kept the Yamaha thrust washer.
I use the Yamaha thrust washer on a Yamaha without issue.
You Don't Know what you Don't Know until you Know.
1984 Champion 201/Yamaha 175
1986 Ranger 390v/Yamaha 200
2002 Viper Cobra Coosa 216/Mercury 225EFI
2002 ProSports ProKat 2200/Twin Yamaha 150HPDIs
You need to use the thrust washer that comes with the Merc flo torq kit for Yamaha motors... The Yamaha thrust washer does not mate to the flo torq style props.... Save those for when you run Yamaha propellers.
Marks Props 317-398-9294, 1850 East 225 South, Shelbyville, Indiana 46176 propellerman59@gmail.com http://www.marksprops.com/index.html
Where can i get the cone bushing and what does it look like? Cant seam to find it. Appreciate the info guys.
Last edited by DUcritter; 07-27-2017 at 06:09 AM.
http://www.mertenmarine.com/Flo-Torq...shing-856163Q1 Here's the part number and a picture of it. If you have been using that Yamaha thrust washer on all the other flo torq hubs that could be why you keep tearing them up.
USN Retired
2020 Basscat Caracal
2020 Mercury 225 ProXS 4s
I'll take one 06 sb! Let me know how much. Zip is 53225.
I wont be home til tomorrow but I will be able to ship it Saturday.
USN Retired
2020 Basscat Caracal
2020 Mercury 225 ProXS 4s
Ok. I'll message u.
Marks Props 317-398-9294, 1850 East 225 South, Shelbyville, Indiana 46176 propellerman59@gmail.com http://www.marksprops.com/index.html