286 DC Pro Tounament
Mercury 200 EFI
fastest to date 78.6 GPS with 26" Lightning ET at 6400
Normally i run, 76.8 GPS with 27" Tempest Plus, worked by Baggie
Just thought i would try to do something for us sprinters.
286 DC Pro Tounament
Mercury 200 EFI
fastest to date 78.6 GPS with 26" Lightning ET at 6400
Normally i run, 76.8 GPS with 27" Tempest Plus, worked by Baggie
Just thought i would try to do something for us sprinters.
1998 286DC Pro Tournament / 1995 Mercury 200 XRI
2000 sprint 221 pro
2000 Merc. 225 EFI
average 72 gps at 5800 running a 25 Tempest +, 3.25" below the pad.
Modified by sprint_lover at 5:50 PM 10/6/2009
.
.
.
.
" The Government cannot give anything that it doesn't first take from someone else"
" A gun in the hand is better than a Cop on the phone "
98 Sprint 207
03 225 Rude DI
73.4 GPS @ 5700 rpms with a Raker 26
T loaded with 2 people 69 GPS with 27 Gade
1998 296 PRO 200hp Johnson(carb)
25p renagade 5800-6000rpm 59.3 gps
I think I need to lower the motor have not checked the height
1998 Sprint 267S
1998 Johnson 90hp SPL
17P 3 Blade Aluminum Prop
39.5 GPS at 5600 RPM WOT
For my first boat...that's plenty fast!!!
1998 207 Pro
200 Merc EFI
25 Tempest +
68.6 GPS WOT 5950 RPM
Jay Peoples
Dont have mine any more....
P&J FISHING ENTERPRISES
\"HIGH PERFORMANCE FISHING\"
"How fast do you want to go?"
[I]Blazer 202 DC - 300 Hammer
WHAT???? First ya stay away and then come back with a tidbit like that!! You OK bud??
1999 296 pro
2001 vmax 200hp (modified )
solo w/ no load 78.7
two persons and gear 75.2
2000 221DC 12" plate jacked throught the roof. Turning 29T1 6000, Powered by Yamaha HPDI, 80 + a litle bit.
<TABLE WIDTH="90%" CELLSPACING=0 CELLPADDING=0 ALIGN=CENTER><TR><TD>Quote, originally posted by LeeinAlabama »</TD></TR><TR><TD CLASS="quote">2000 221DC 12" plate jacked throught the roof. Turning 29T1 6000, Powered by Yamaha HPDI, 80 + a litle bit. </TD></TR></TABLE>
A little bit.....Yea.... Where ya been prodigal??
Man....work work work....need buy props......work work work....
P&J FISHING ENTERPRISES
\"HIGH PERFORMANCE FISHING\"
"How fast do you want to go?"
[I]Blazer 202 DC - 300 Hammer
I'm here.
Been doing the TBF and Federation Nation trails. We are done until the Championships this fall.
Well, the OTHER prodigal shows up!!! Glad to hear from ya both!!
'91 275
Mid 80's 2.4 liter 200HP Mariner
6" Vance Manual Jackplate
62MPH (gps) turnina a 26P Turbo M 6,000 RPM 3.25" below the pad with some hot foot left but wouldn't go any more cause the oil injection is still hooked up.
Got a 27P A40 Tempest on the way. Will update when I get it installed and tested a bit.
Got the 27P A40 Tempest on. Hole shot is real slow, but once up, I bumped 70mph on the GPS @ 6,000 RPM. I also raised the motor a little.
Modified by Rooster Tails at 9:48 AM 8/24/2009
Modified by Rooster Tails at 2:42 PM 11/16/2009
Rooster Tails
Sprint 275/200 Mariner
Central Louisiana
99 DC 207 Limited with a 225 Mariner Super Mag on a manual plate up about 3 inches. 62+ with a 24pitch at 5300 and 62+ with a 22pitch at 6000 but with this prop the speed is still increasing so I dont know what top end would be. The lakes here in Mass are not that big.. How long does it take to get to top end with a rig like mine??
Wes Billings
FTC/SS USN Retired
1998 277 Pro Tournament
1998 Promax 2.5L 150
24P Fury Prop
66.1 GPS @ 6350 RPM
2000 Pro Tournament 286
Mercury 150xr6
56.0 GPS turning 5600 rpms
thinking i need to get a 6" jackplate to get the back end out of the water and maybe hit 60
1998 Sprint 277 Pro
2.6L HydroTec built Yamaha
Motor was a 150, still has 2.0 gears
Prop, 29 Tempest worked by Jay Martin Propellers
Top speed 83.4 @ 6200 rpm
99 221 DC with 225 Merc EFI---running a 26 Trophy hit 76.1 with a very light load. Not the best holeshot.
I usually run a 25 Trophy to carry a load and with two and a decent load can still run 73-74 GPS with not too much problem---turning 5800.
I have done a few little mods to the motor---switched to 250 Fuel ECM, changed to newer style 4 butterfly intake manifold,cut exhaust tuner,Simons solid motor mounts,Simons Popit Valve, Boyesen Reeds and modded cowling(raised with air holes cut in them)
Runs real good! I am happy. I removed the trolling motor to do some work to it and want to run it without a troller to see how much it will pick up the nose.
I will let you all know.