Bow roller replacement?

[kry29]

I got mine in today. Put them on and the boat fits a lot better. My next issue is my boat always sits a tad to the left side of the roller so I might have to adjust my bunks a hair

[BigSexyPhoenix]

I noticed mine was sitting just a tad to the left too. Not even enough to notice unless you're right down staring at it up close. I figure I'm not going to worry about it anymore and just fish. I'll try to get the scratches out and call it good.

[DREWTICK]

Someone will find something else for all of us to change, adjust, spend money on next month.

[kry29]

Someone will find something else for all of us to change, adjust, spend money on next month.

That's the truth! It's always something. Lol

[wcookieman]

I have 2011/721 tried to lift bow and no luck. I looked at the bunk but don't see that they can be adjusted.

[ShawnD]

I have 2011/721 tried to lift bow and no luck. I looked at the bunk but don't see that they can be adjusted.

I've got a 2015 618 and can't lift the bow.
Trailers perfect and loads better than most boats at the ramp loll

[MJL]

got mine replaced today, buffed out the scuff marks also.

What's the best method for buffing off the marks?

[DREWTICK]

Bluebird or crank68 can probably chime in with some professional advice but I used a 3 step process
Started with a wool pad with a polishing compound
Then a foam pad with a 3m finishing liquid
Then protech sealent
Careful with the wool pad if you are using a high speed buffer you don't want to get the gel coat hot.

[6xd]

I spoke with marine master today and had a lengthy discussion, we agreed the ramp pitch is a major factor. He told me they have only send out 6 shim packs to date.

[6xd]

Drew, what are part #s, the Ult 4 or 444 and 434

[BigSexyPhoenix]

I spoke with marine master today and had a lengthy discussion, we agreed the ramp pitch is a major factor. He told me they have only send out 6 shim packs to date.

Probably the same guy I spoke with that told me we basically didn't know how to load boats onto trailers even though none of my other boats did this. I just ordered a new roller so I didn't have to even deal with him again because I could tell it wasn't going to end good. New roller seems to be working fine.

[6xd]

Ya, I had some questions about my rotors and he started getting a little pissy.

[DREWTICK]

Drew, what are part #s, the Ult 4 or 444 and 434

444 and 435

[BigSexyPhoenix]

Ya, I had some questions about my rotors and he started getting a little pissy.

Was his name Jeff?

[wtrwsel]

Well since it's the season to change out bow rollers, I did mine as well. Ordered the Ult-4 off of the auction site for $40 shipped, seemed pretty fair. Looks good and not an eyesore anymore. Now to get my fading Phoenix stickers on the trailer replaced. Anyone know where to get them?

[DREWTICK]

Well since it's the season to change out bow rollers, I did mine as well. Ordered the Ult-4 off of the auction site for $40 shipped, seemed pretty fair. Looks good and not an eyesore anymore. Now to get my fading Phoenix stickers on the trailer replaced. Anyone know where to get them?

https://phoenix-boat-apparel.myshopi...ns/accessories

[5pigs]

I guess I will change my bow roller. Crushed out with a gap on both side rollers that might catch the Vee.

[laposta28]

When replacing use the existing bolt or the one sent by Stolz with the RP 444 and Rp 435?

[DREWTICK]

When replacing use the existing bolt or the one sent by Stolz with the RP 444 and Rp 435?

.
what ever works best, just make sure if you use the original that its not bent, and dont over tighten the roller needs to be free

[laposta28]

Thanks!!!!