yes fred thats right. number 2 isnt firing. the orange leads are correct ive checked them like 20 times lol.
yes fred thats right. number 2 isnt firing. the orange leads are correct ive checked them like 20 times lol.
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Try your old pack now and see how it does.
ok fred. ill try it and get back with you
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
fred im about to pull what little bit of hair i have left out. got a new powerpack and i finally have fire on all 6. so that problem finally got solved. took it to the lake and cranked it. it will barely idle ans will not run in gear. no matter what i try with the screws. its in tdc with the pointer. tried to set the timing in gear unrestrained @ 4 atdc and it wont run for about 5 - 10 seconds. i rememberd to try and push in the choke and it actually idled and ran in gear as soon as i let off the key about 10 seconds it would die again. so trying the choke is helping it. what should i try next? it didnt run like this at all until the timer base and power pack change. it used to fire 4-5 but idled great.
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Chris try this. Loosen the lock nut on the idle timing screw and set the screw to 1" off the end of the linkage arm, that should get you close. Set all of your carb idle jets to 5 full turns out that is the initial setting. Set it in neutral first and check your RPMs. 900 is OK it will drop once you drop it in gear. Make sure you have the throttle cable disconnected so your adjustments aren't hindered by cable binding.
ok fred i tried yesterday. no luck. it wont idle long and it def wont in gear. another question for you. im looking at buying a parts motor that is blowed up. its a 1999 j200pleeb. suppose to be a 200 ho. will the fuel pump and alot of other parts fit mine? im hoping if my carbs and stuff needs rebuilt i can use those. would the jets have to be swapped over?
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Chris everything will bolt right on to your block, there never was a 200 HO only 225's HO's and only for 3 years. Those model numbers are all 225HGL model numbers. Same carbs just move the orifices over.
ok fred i picked it up lastnight. its locked up for sure. it doest have a lower unit on.would pulling the heads help determine why it locked up
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Yep. My guess it will be something to do with the #2 cylinder.
ok ill pull them off and take some pictures. thanks brother i appreciate all the help you have done for me and others thru the years
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
and if i decide to move the carbs do i just need to move the 2 orifices over thats it? and ofcourse the drain screws if they arent the updated ones
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Yep that will work.
if im not mistaken #4 is bad. if your behind the motor looking at port side middle one. i checked the carb drain screw and jet they were seated good. if your looking at the carbs middle left one
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Yep #4 Check the #4 carb. gonna be the middle one on the left facing them and see if it has the new style drain screw on it with the raised tit on it. Looks like it got hot and started to lose the wrist pin bearings.
Yep #4 Check the #4 carb. gonna be the middle one on the left facing them and see if it has the new style drain screw on it with the raised tit on it. Looks like it got hot and started to lose the wrist pin bearings. Along with some water intrusion in that cylinder.
fred it does have the drain with " tits" and it seemed tight. the high speed jet behind it was fully seated
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
i believe the flywheel key is sheared
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY
Chris Owenby Owner
Smoky Mountain Jigs.com
Hand Tied Jigs, Spinnerbaits and much more
2000 Skeeter zx202c - 200 Yamaha Vmax OX66 VX200TLRY