Results 1 to 11 of 11
  1. #1
    Member
    Join Date
    Sep 2014
    Location
    Lufkin Tx
    Posts
    264

    Swapping from a 21p Solas blade to a 21p Trophy Plus

    I currently have a 21p Solas HR Titan 4 prop on my 150 Opti. I have a chance to potentially buy a 21p Trophy Plus. What would the difference (if any) between the two props be as far as top speed and rpm's? The Solas turns 54 mph (gps) at 5250 rpm's.
    2011 Legend Alpha 211 DC
    250 Pro XS
    Solix 10 G2 MSI & Onix 10 NT
    Elite 9 Ti2 connected to
    Motorguide Xi5 105

  2. Member
    Join Date
    Feb 2016
    Location
    Musella Georgia
    Posts
    209
    #2
    when I purchased my procraft with a 150 efi it had a 21 tempest at 60 mph on limiter at 6150 there about. you need the lift of the tempest with the nitro. I said that to say you can probably come up with the motor for more rpm's. I have not been impressed at all with the solas props. both being 21 p. the rpm's should be close. I would give both top speed and rpm's to the tempest. solas is a through hub, is that right?

  3. Member
    Join Date
    Sep 2014
    Location
    Lufkin Tx
    Posts
    264
    #3
    The Solas is a through the hub prop. You're referencing a tempest, but I'm looking at a trophy . Any ideas how those 2 would compare?
    2011 Legend Alpha 211 DC
    250 Pro XS
    Solix 10 G2 MSI & Onix 10 NT
    Elite 9 Ti2 connected to
    Motorguide Xi5 105

  4. Member
    Join Date
    Feb 2016
    Location
    Musella Georgia
    Posts
    209
    #4
    I now see you were speaking of a trophy. i was trying to fix my mistake. the trophy imo would give a little better speed on t.e.. sorry for the confusion. I think the tempest would be your best shot but would try to raise the motor before buying.
    Last edited by gaboy; 04-29-2016 at 07:25 PM.

  5. Member
    Join Date
    Feb 2016
    Location
    Musella Georgia
    Posts
    209
    #5
    I will get off the tempest, it is a 3 blade and will run about 100-150 rpms higher than the 4 blade.

  6. Member
    Join Date
    Feb 2016
    Location
    Musella Georgia
    Posts
    209
    #6
    what is your motor height? the rpm's are low.

  7. Member
    Join Date
    Sep 2014
    Location
    Lufkin Tx
    Posts
    264
    #7
    Motor is at 3 1/4" below pad. When I've raised it higher the handling seems to get pretty loose. I have a Tempest 24p. I get about the same speed just with higher rpms... 5450. I've thought about getting a 23p in the tempest, but Idk if it would be much better.
    2011 Legend Alpha 211 DC
    250 Pro XS
    Solix 10 G2 MSI & Onix 10 NT
    Elite 9 Ti2 connected to
    Motorguide Xi5 105

  8. Member
    Join Date
    Jul 2010
    Location
    Yorktown, VA
    Posts
    65
    #8
    It is very unlikely you are getting higher RPMs with a 24p vs a 21p. The 21p is smaller in diameter and will turn more to achieve the same speed. Going from a 3 blade to a 4 blade prop usually results in a 100-200 RPM drop. A 4 blade provides better mid range power and control usually but lacks too end speed.

  9. Member
    Join Date
    Sep 2014
    Location
    Lufkin Tx
    Posts
    264
    #9
    I know it sounds weird... I'm just going good by what the tach is showing...
    2011 Legend Alpha 211 DC
    250 Pro XS
    Solix 10 G2 MSI & Onix 10 NT
    Elite 9 Ti2 connected to
    Motorguide Xi5 105

  10. Member Cousin-It's Avatar
    Join Date
    Feb 2011
    Location
    Pensacola
    Posts
    1,593
    #10
    Quote Originally Posted by rcraigrrt View Post
    I know it sounds weird... I'm just going good by what the tach is showing...
    I have a 18.5 Astro which was Pro=Craft,150 EFI merc and when I got it had no hole shot or it would no lay over for rough water it had a 21 pitch prop.I had a chance to buy a 23 tempest plus and its great think it may or could go to a 24 pitch.It use to turn 6700 with the 21 and now with the 23 it turns 5800 at WO at 58-60 mph on GPS.
    Still chasing the green fish

  11. Member
    Join Date
    Sep 2014
    Location
    Lufkin Tx
    Posts
    264
    #11
    I guess I'll find out soon... I went ahead and bought the Trophy and will see what happens... after looking, the trophy is a 13 3/4" diameter prop where the Solas is a 14" prop. So I'm hoping for a few more rpms and maybe a Lil more speed.
    2011 Legend Alpha 211 DC
    250 Pro XS
    Solix 10 G2 MSI & Onix 10 NT
    Elite 9 Ti2 connected to
    Motorguide Xi5 105