I assume way different. Mine is a Viper.... if there is a panel in the front, use your phones video camera and record what it looks like underneath.
I assume way different. Mine is a Viper.... if there is a panel in the front, use your phones video camera and record what it looks like underneath.
Sent you the info in a PM. Did you get it?Originally Posted by The Heater
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Yes Sir. Thank you
Larry, could you please send me the info via email? Thank you!
1997 Viper Coral 202
1998 Mercury 200 EFI
Larry you're a popular guy... I have a 2000 190 and want to do a trolling motor tray.. Please send me the most important email on the planet?
roba26@hotmail.com
thank you , if you ever come to Colorado I can show you the smallest bass on the planet :)
Not all churches have pews? Very few churches without pews have God.
Check your personal messages.
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Ding, ding, check your eMail.
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Would love the info for this also.
Sent it to you in a personal message.
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Hey Larry, I haven’t been on in a while so bear with me!
I want to put a recessed tray in my 2003 201 coosa and could use all the help I can get.
Could use your instructions ! Also wondering if you know anyone that has changed that
switch panel with toggle switches? Thanks, Dave
Dave, Sent the instructions for the Recessed Trolling Motor Pedal via a personal message. As for your question about toggle switches are these what your looking for? https://newwiremarine.com/marine-gra...switch-covers/
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Hey Larry, if I could get this info that would be great. jhamill@purgatory.ski
Cheers
Cobra Coosa 201
Ding,Ding, check your eMail.
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Only help I'll offer is, do it. You'll have no regrets at all and wish you'd done it sooner. I did an old Ranger, I made a template out of plywood for the hole in the deck. Set it in place and plunge cut around the template with the saw set no deeper than the thickness of he deck. Then trimmed the corners out with a sawzall. Just take the time to locate the hole for your fishing style. Put the seat in and find out what the best location is.
2017 Phoenix 819
2016 200ProXS, s/n 2B359849, Mod 1200P73BD
Hello, Could you please email me the instructions as well? Much appreciated.
If you could send the instructions for the Recessed Trolling Motor Pedal to me as well, I would greatly appreciate it!
Ray...Ding, Ding you have mail.
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Would love to have this info as well please. Cobra 190. Thanks!
Ding, ding, check your eMail!
I thought I would be on Easy Street by now but somehow I missed the off ramp!
Just wanted to give some insight. I have a '96 cobra 201D. I recently installed a recessed tray. 2 major tips to help you out. Buy a painters drop cloth ($2) and covered the area while doing the cut out to save fiberglass from getting on your floor. Its a messy job. 2nd and most importantly. I went 13" forward from the front seat post per install recommendations. DO NOT go any further forward. My boat had a fiberglass enclosure that held the foam. You can see where i drilled a hole in it to place the drain hose for the recessed tray. I would of had to cut through had i went an inch more forward potentially exposing the foam to significant moisture. The foam is a pain to cut out but just takes a little extra time. Hope this helps anyone in the future looking to do this install. I used polyurethane on the exposed wood to help seal it after I cut through the deck and used silicone on all the screws and around the lip of my recessed tray during the install to help keep moisture out as well.
Reply With Quote