Thanks for the clarification Wayne, that makes sense now.
Button.... Does your 2d transducer cause an interference line on the side scan view just right of the center line?
Thanks for the clarification Wayne, that makes sense now.
Button.... Does your 2d transducer cause an interference line on the side scan view just right of the center line?
Has anybody figured out placement yet on this hull where readings are consistant at all speeds?
Roy
2020 Triton 18 Trx
Mercury 200 Pro XS V8
Bravo FS 24P Prop
Atlas 6” jp
Dual Humminbird Helix 10 MEGA SI
Minnkota Ultrex.
the 2d does not cause an interference line. The live well intake is the one causing the line. but its not a big deal..it is less now.
I have the triton X17 (which has the same hull). I am running a merc 75 optimax and the factory Lowrance Depth finder (not a DI type finder, lower end 2d)... I can read at WOT (39 mph, 5500 rpm) without and issue usually. The only interference I see is when I first engage the motor in gear
I lose I very now and then tho ... I'll post my mount location
Thread back from the dead.
When mounting these boards for the TD's are you guys just drilling and using sheet metal screws to hold the board on are do you drill thru and put bolts and nuts to hold board or TD for that matter?
I will be installing a regular sonar TD for a Helix 7 this week, I want a board long enough to first try mounting the TD inline with the bunk as that looks like the best place to put it since that welded piece of angle is in the other best place!
2022 Xpress H17 - Yamaha SHO 90
They come with screws, thats what i used, and alot of clear marine grade silicone in the holes and on the screws. It doesnt leak.
Last edited by stratos284; 04-30-2016 at 08:14 AM.
2022 Xpress H17 - Yamaha SHO 90
2023 Ranger RT188P
2023 Mercury Pro XS 115
Garmin 126SV (2), 93SV, LVS34
Minn Kota Ultrex
This is the one i used, theres a bunch of them on amazon for cheap.
http://www.amazon.com/Custom-Tackle-...mounting+board
2022 Xpress H17 - Yamaha SHO 90
2014 Ranger RT188
115 Merc 4s, laser II 20p
humminbirds
2023 Ranger RT188P
2023 Mercury Pro XS 115
Garmin 126SV (2), 93SV, LVS34
Minn Kota Ultrex
At first I did get a rooster tail that would splash the side of the motor, a little electrical tape across the
gap at top of transducer mount fixed that problem. This is a pic after first mounted, I also moved it upward about an inch.
Last edited by fishinSteve; 04-30-2016 at 12:41 PM.
2014 Ranger RT188
115 Merc 4s, laser II 20p
humminbirds
Do you get good on plane readings with it there?
I'll just be mounting a regular sonar TD but would like to get readings while on plane.
I'm going to first try mounting the TD in line with the bunk area since my bunks are not to going to hit the TD while the boat is on the trailer due to the bunks setting @ 1/2" under the boat.
2022 Xpress H17 - Yamaha SHO 90
My signature shows readings at 50mph
2014 Ranger RT188
115 Merc 4s, laser II 20p
humminbirds
2022 Xpress H17 - Yamaha SHO 90
This is where it is right now, notice the tape (keeps it from blowing a rooster tail against the cowling).
I don't know why it turned this pic sideways...but...
2014 Ranger RT188
115 Merc 4s, laser II 20p
humminbirds
2013 Pre-Johnny Ranger RT 178
115 PRO XS
Due to the increase of ammunition prices... There will be no warning shots
Honda certified Master technician 33 Years
I bought one called a sternmate off ebay and have been thinking about mounting it behind the bunk board. But now that I see where Steve has his located I might change my mind. Has anybody just used glue without screws.